View NAS400_7784900.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

e dge s tore NAS400 user manual version 1.0 ? s t e r r e i c h : t e l . : 0 1 / 5 8 5 5 4 3 0 f a x : 0 1 / 5 8 5 5 4 6 0 d e u t s c h l a n d : t e l . : 0 7 6 1 / 5 9 2 1 0 0 f a x : 0 7 6 1 / 5 8 5 2 2 8 s c h w e i z : t e l . : 0 6 1 / 2 7 3 1 1 - 3 1 f a x : 0 6 1 / 2 7 3 1 1 - 3 9 h a n t z + p a r t n e r t h e u p g r a d e c o m p a n y ! w w w . h a n t z . c o m free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual ii copyright ? 2007 edge10 corporation limited. all rights reserved. copyright by edge10 corporation limited. (edge10). no part of this manual may be reproduced or transmitted in any form without the expressed, written permission of edge10. important data protection information you should back up all data before installing any drive controller or storage peripheral. edge10 is not responsible for any loss of data resulting from the use, disuse or misuse of this or any other edge10 product. notice although edge10 has attempted to ensure the accuracy of the content of this manual, it is possible that this document may contain technical inaccuracies, typographical, or other errors. edge10 assumes no liability for any error in this publication, and for damages, whether direct, indirect, incidental, consequential or otherwise, that may result from such error, including, but not limited to loss of data or profits. edge10 provides this publication ?as is? without warranty of any kind, either express or implied, including, but not limited to implied warranties of merchantability or fitness for a particular purpose. the published information in the manual is subject to change without notice. edge10 reserves the right to make changes in the product design, layout, and driver revisions without notification to its users. this version of the user manual supersedes all previous versions. recommendations in this user manual , the appearance of products made by other companies, including, but not limited to software, servers, and disk drives, is for the purpose of illustration and explanation only. edge10 does not recommend, endorse, prefer, or support any product made by another manufacturer. free datasheet http://www.datasheet-pdf.com/
iii contents chapter 1: introduction to edgestore . . . . . . . . . . . . . . . . . . . . . . . . .1 about this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 protocol support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 key benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 compatible backup software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 client os support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 browser support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 chapter 2: installation and setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 unpacking the edgestore NAS400 . . . . . . . . . . . . . . . . . . . . . . . . . .5 installing disk drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 connecting to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 connecting the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 optional. selecting your network . . . . . . . . . . . . . . . . . . . . . . . . . .12 setting up the edgestore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 connecting to easm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 browser support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 finding the edgestore?s ip address . . . . . . . . . . . . . . . . . . . . .17 easm in your browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 easm in smartsync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 shutting down the edgestore . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 chapter 3: connecting to the edgestore . . . . . . . . . . . . . . . . . . . . . .21 setting up a network drive on a windows pc . . . . . . . . . . . . . . . .21 setting up a network drive on a unix or linux pc . . . . . . . . . . . .24 setting up a network drive on a macintosh pc . . . . . . . . . . . . . . .27 connecting a usb printer to edgestore . . . . . . . . . . . . . . . . . . . . .31 setting up the print server on edgestore . . . . . . . . . . . . . . . . . . . .32 setting up windows printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 setting up linux printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 setting up macintosh printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 connecting a usb drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 disconnecting a usb drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual iv chapter 4: one touch backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 enabling one touch backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 creating a backup schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 performing a one touch backup . . . . . . . . . . . . . . . . . . . . . . . . . .45 viewing your backup files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 restoring your backup files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 chapter 5: smartsync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 opening the smartsync window . . . . . . . . . . . . . . . . . . . . . . . . . .49 choosing a language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 closing the smartsync window . . . . . . . . . . . . . . . . . . . . . . . . . .50 quitting smartsync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 displaying the edgestores on your network . . . . . . . . . . . . . . . . . .50 starting easm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 connecting a network drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 deleting device (network drive) records . . . . . . . . . . . . . . . . . . . .53 performing a backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 viewing your backup folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 performing a restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 scheduling a backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 modifying a backup schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 deleting a backup schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 setting the default browser for easm . . . . . . . . . . . . . . . . . . . . . .58 viewing the event log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 clearing the event log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 saving the event log to a text file . . . . . . . . . . . . . . . . . . . . .58 chapter 6: easm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 connecting to easm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 easm in your browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 easm in smartsync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 choosing a language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 navigating in easm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 setting up edgestore with the setup wizard . . . . . . . . . . . . . . . . .63 managing users and groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 viewing a list of users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 creating a user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 changing the administrator?s password . . . . . . . . . . . . . . . . . .65 changing a user's password . . . . . . . . . . . . . . . . . . . . . . . . . .66 deleting a user . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 viewing a list of groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 free datasheet http://www.datasheet-pdf.com/
contents v chapter 6: easm, cont. managing users and groups, cont. creating a group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 adding members to a group . . . . . . . . . . . . . . . . . . . . . . . . . . .67 removing members from a group . . . . . . . . . . . . . . . . . . . . . .67 deleting a group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 viewing quotas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 setting quotas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 managing file & print services . . . . . . . . . . . . . . . . . . . . . . . . . . . .70 setting up windows access . . . . . . . . . . . . . . . . . . . . . . . . . . .70 setting up unix/linux access . . . . . . . . . . . . . . . . . . . . . . . . .71 setting up for macintosh access . . . . . . . . . . . . . . . . . . . . . . . .72 setting up for ftp access . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 setting up your print server . . . . . . . . . . . . . . . . . . . . . . . . . . .74 setting up your dlna server . . . . . . . . . . . . . . . . . . . . . . . . . .74 viewing a list of folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 modifying folder services . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 adding a folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 deleting a folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 setting up windows sharing for a folder . . . . . . . . . . . . . . . . .77 setting up unix and linux sharing for a folder . . . . . . . . . . . .77 setting up ftp sharing for a folder . . . . . . . . . . . . . . . . . . . . .78 managing raid volumes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 viewing raid volume status . . . . . . . . . . . . . . . . . . . . . . . . . .79 viewing disk drive information . . . . . . . . . . . . . . . . . . . . . . . . .80 creating a raid volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 designating a spare drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 migrating a raid volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 deleting a raid volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 viewing an external usb drive or memory stick . . . . . . . . . . .83 formatting an external usb drive or memory stick . . . . . . . . .83 managing backups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 viewing a list of snapshot backups . . . . . . . . . . . . . . . . . . . . .84 setting up a snapshot backup . . . . . . . . . . . . . . . . . . . . . . . . .84 scheduling a snapshot backup . . . . . . . . . . . . . . . . . . . . . . . .85 recovering snapshot backups . . . . . . . . . . . . . . . . . . . . . . . . .85 viewing the nas replication schedule . . . . . . . . . . . . . . . . . .86 setting up nas replication . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 enabling one touch backup . . . . . . . . . . . . . . . . . . . . . . . . . .87 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual vi chapter 6: easm, cont. managing the network connection . . . . . . . . . . . . . . . . . . . . . . . . .88 viewing network setup information . . . . . . . . . . . . . . . . . . . . .88 making network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88 working with jumbo frames . . . . . . . . . . . . . . . . . . . . . . . . . .89 setting up your ddns service . . . . . . . . . . . . . . . . . . . . . . . . .90 making management settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 viewing service status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91 viewing the event log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92 setting up smtp authentication . . . . . . . . . . . . . . . . . . . . . . . .92 viewing the email alert list . . . . . . . . . . . . . . . . . . . . . . . . . . .93 adding an email alert recipient . . . . . . . . . . . . . . . . . . . . . . . .93 deleting an email alert recipient . . . . . . . . . . . . . . . . . . . . . . .93 upgrading the system firmware . . . . . . . . . . . . . . . . . . . . . . .93 installing an application plug-in . . . . . . . . . . . . . . . . . . . . . . . .93 enabling and disabling the buzzer . . . . . . . . . . . . . . . . . . . . . .94 viewing ups status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94 setting up a ups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 managing services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96 setting system date and time . . . . . . . . . . . . . . . . . . . . . . . . .96 running the network time protocol . . . . . . . . . . . . . . . . . . . . .96 viewing the results of ntp synchronization . . . . . . . . . . . . . .97 rebooting the edgestore . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97 shutting down the edgestore . . . . . . . . . . . . . . . . . . . . . . . . . .98 restarting the edgestore . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 locating the edgestore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 viewing system information . . . . . . . . . . . . . . . . . . . . . . . . . . .99 viewing enclosure information . . . . . . . . . . . . . . . . . . . . . . . . .99 chapter 7: technology background . . . . . . . . . . . . . . . . . . . . . . . .101 introduction to raid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101 raid 0 ? stripe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 raid 1 ? mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 raid 5 ? block striping with distributed parity . . . . . . . . . . . .104 raid 10 ? mirror / stripe . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105 choosing a raid level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 raid 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 raid 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106 raid 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 raid 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 free datasheet http://www.datasheet-pdf.com/
contents vii chapter 7: technology background, cont. spare drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 automatic rebuilding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 partition and format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108 raid volume migration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 raid 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 raid 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109 raid 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 raid 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 chapter 8: troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111 responding to an audible alarm . . . . . . . . . . . . . . . . . . . . . . . . . .111 checking the system status led . . . . . . . . . . . . . . . . . . . . . . . . .112 checking disk status leds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112 replacing a failed disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 checking raid volume status in easm . . . . . . . . . . . . . . . . . . . .113 edgestore responds to a critical raid volume . . . . . . . . . .114 responding to an invalid raid volume . . . . . . . . . . . . . . . . .114 checking file system status in easm . . . . . . . . . . . . . . . . . . . . .115 rebuilding the file system . . . . . . . . . . . . . . . . . . . . . . . . . . .116 checking the event log in easm . . . . . . . . . . . . . . . . . . . . . . . . .116 responding to events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 checking enclosure status in easm . . . . . . . . . . . . . . . . . . . . . .120 resolving connections with smartsync . . . . . . . . . . . . . . . . . . .121 multiple network connections . . . . . . . . . . . . . . . . . . . . . . . .122 solving network connection problems . . . . . . . . . . . . . . . . . . . . .123 checking your email inbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124 restoring the default password . . . . . . . . . . . . . . . . . . . . . . . . . .124 resolving a windows firewall issue . . . . . . . . . . . . . . . . . . . . . . .125 chapter 9: support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 contacting technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . .130 limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131 returning product for repair . . . . . . . . . . . . . . . . . . . . . . . . . . . .133 appendix a: smartwizard advanced mode . . . . . . . . . . . . . . . . . .135 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual viii appendix b: maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 upgrading the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143 rebooting the edgestore . . . . . . . . . . . . . . . . . . . . . . . . . . . .144 installing application plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 connection problems after restart . . . . . . . . . . . . . . . . . . . . . . . .146 appendix c: gnu general public license . . . . . . . . . . . . . . . . . . .147 index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149 free datasheet http://www.datasheet-pdf.com/
1 chapter 1: introduction to edgestore ? about this manual (page 1) ? architecture (page 2) ? protocol support (page 2) ? key benefits (page 2) ? specifications (page 3) ? compatible backup software (page 4) ? client os support (page 4) ? browser support (page 4) edge10?s edgestore NAS400 is a network attached storage (nas) solution for external storage targeted for small and medium business (smb) users and small office/home office (soho) users. with a nas product, users can save their work and have access to files over the network without having to carry around a disk drive or memory stick. the administrator can manage access privileges for greater security. multiple backup and synchronization functions protect your data. about this manual this product manual describes how to setup, use, and maintain the edgestore NAS400. it also describes how to use the nas setup wizard, smartsync utility, and edge10 advanced storage manager (easm) software. this manual includes a full table of contents, chapter task lists, and numerous cross-references to help you find the specific information you are looking for. also included are four levels of notices: note a note provides helpful information such as hints or alternative ways of doing a task. important an important calls attention to an essential step or point required to complete a task. important items include things often missed. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 2 architecture the edgestore NAS400?s architecture is based on the freescale mpc8343 microprocessor and the promise pdc40719 serial ata raid controller. the gigabit ethernet port is used for the data transfer and management. the usb ports are used for a printer, expansion drives, and uninterruptable power supply (ups). protocol support edgestore NAS400 supports: ? windows 2000, xp professional, 2003 server; and vista business, enterprise, and ultimate clients through smb and cifs protocols ? unix and linux clients through the nfs protocol ? macintosh clients through the afp protocol ? ftp clients through the ftp protocol ? dlna clients through upnp protocol with an optional plug-in ? up to 16 concurrent connections key benefits ? easy-to-use browser-based management interface ? data sharing over the network ? one-touch backup of designated file folders on client pc ? snapshot backup for real-time image of the file system ? remote nas-to-nas synchronization and backup ? network print server with usb printer ? user, group, and quota management ? ups support with automated shutdown ? heterogeneous environment: windows, unix, linux, and macintosh caution a caution informs you of possible equipment damage or loss of data and how to avoid them. warning a warning notifies you of probable equipment damage or loss of data, or the possibility of physical injury, and how to avoid them. free datasheet http://www.datasheet-pdf.com/
chapter 1: introduction to edgestore 3 ? smartsync backup utility ? setup wizard utility specifications ? disk drive support: ? four 1.5 gb/s or 3 gb/s sata 3.5-inch disk drives ? conforms to serial ata 1.0 specification and serial ata ii: extensions to serial ata 1.0 specification (sata ii, phase i specification) ? sata specification of 3 gb/s transfers with crc error-checking ? hot-swapping of disk drives ? tagged command queuing ? native command queuing ? drive roaming among channels ? s.m.a.r.t. status polled every 15 minutes ? online capacity expansion ? raid level migration ? hot spare drives ? raid volume rebuilding ? gigabyte rounding ? background rebuilding ? raid level support: raid 0, 1, 5, and 10 ? large file system support up to 4 tb ? unicode file name support ? sata raid controller: promise pdc40719 ? server on a chip: freescale mpc8343, 400mhz ? networking: 10/100/1000 mb/s ethernet port on motherboard ? usb ports: usb 2.0, up to 480 mb/s, two type-a connectors ? file protocols: smb, cifs, ftp, afp, nfs ? flash memory: 16 mb, 16-bit ? memory: 128 mb ddr sdram ? power supply: 200-watt atx with pfc ? network time protocol (ntp) client ? error logging ? phone home capability (email notification) to contact it staff free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 4 ? hardware monitoring of: compatible backup software edgestore NAS400 is compatible with the following backup software products: ? veritas? netbackup/backup exec? ? ca brightstor?arcserve/enterprise ? legato? networker? ? syncsort backup express ? microsoft backup software for windows 95/98/nt/2000/me/xp ? dantz retrospect for macintosh client os support microsoft windows: ? vista business, enterprise, and ultimate; server 2003, xp professional, 2000 ? supports intel ia32, amd64 and intel em64t platforms unix/linux: ? red hat enterprise linux 3.0 (as/ws/es) ? red hat enterprise linux 4.0 (as/ws/es) ? suse linux enterprise 10 (server/desktop) apple macintosh: ?macos x browser support use the latest version of the following browsers to manage the edgestore NAS400: ? internet explorer ? netscape navigator ? mozilla ?firefox ? safari (macos x) ?fan ? temperature ?power ? disk status ? one-touch button ? enclosure status free datasheet http://www.datasheet-pdf.com/
5 chapter 2: installation and setup ? unpacking the edgestore NAS400 (page 5) ? installing disk drives (page 7) ? connecting to the network (page 7) ? connecting the power (page 8) ? installing the software (page 8) ? optional. selecting your network (page 12) ? setting up the edgestore (page 13) ? connecting to easm (page 17) ? shutting down the edgestore (page 20) unpacking the edgestore NAS400 the edgestore NAS400 box contains the following items: ? edgestore NAS400 unit ?quick start guide ? screws for disk drives (16, including 4 spares) ? ethernet cable ? 1.5m (4.9 ft) power cord ? cd with nas setup wizard, smartsync software, and configuration tool, product manual and quick start guide warning the electronic components within the edgestore are sensitive to damage from electro-static discharge (esd). observe appropriate precautions at all times when handling the edgestore or its subassemblies. important to configure the edgestore, you must install the software onto a pc running windows vista business, enterprise or ultimate; 2003 server, xp professional, or 2000. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 6 figure 1. edgestore NAS400 front view figure 2. edgestore NAS400 rear view disk drive drive carrier disk activity led power button ethernet activity led one touch backup button disk status led note: this edgestore is shown without the front door. system status led power connection usb connections rj45 network connection disk drive cooling fan power supply fan free datasheet http://www.datasheet-pdf.com/
chapter 2: installation and setup 7 installing disk drives you can populate the edgestore NAS400 with sata 1.5 gb/s or 3.0 gb/s disk drives. for optimal performance, install disk drives of the same model and capacity. your disk drives will beco me a raid volume on the edgestore. to install disk drives: 1. open the door on the front of the edgestore enclosure. 2. pull a disk drive carrier from the enclosure. see figure 1. 3. carefully lay the disk drive into the drive carrier, so that the screw holes on the sides of the carrier align with the screw holes in the drive. 4. insert the screws through the holes in the drive carrier and into the sides of the disk drive. ? install only the counter-sink screws supplied with the edgestore. ? install four screws per drive. ? snug each screw. be careful not to over-tighten. 5. reinstall the drive carrier into the edgestore enclosure. repeat steps 2 through 5 until all of your disk drives are installed. 6. close the door on the front of the edgestore. connecting to the network to connect the edgestore to your network: 1. attach one end of the network cable to the rj45 network connection. see figure 2. 2. attach the other end of the network cable to your ethernet hub or switch. important if there are multiple networks at your facility, note the network to which you connect the edgestore. you will need this information during the setup process. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 8 connecting the power to power the edgestore: 1. attach the power cord on the back of the edgestore enclosure and plug the other end into the power source. see figure 2. 2. on the front of the edgestore, press the power button. see figure 1. it takes about a minute to boot the edgestore. when fully booted: ? the system status led turns green. see figure 1. ? the buzzer beeps one time. installing the software when you install the software onto your windows pc, three new items are added to the windows start menu: ? smartwizard ? sets up the edgestore ? smartsync ? connects your pc to the edgestore, sets up network drives on your pc, and performs backups ? configure tool ? ensures that the edgestore, smartwizard, and smartsync are all on the same network to install the software: 1. insert the cd into your cdrom. 2. double-click the nas utility installer icon. the choose setup language dialog box appears. 3. choose your setup language from the dropdown menu. click the ok button. free datasheet http://www.datasheet-pdf.com/
chapter 2: installation and setup 9 the first installer screen appears. 4. click the next button to begin installation. the license agreement screen appears. 5. click the ?i accept the terms...? option, then click the next button. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 10 the customer information screen appears. 6. type a user name and organization name into the respective fields or leave them unchanged to accept the default entries. click the install option for: ? anyone who uses this computer (all users) ? only for me (the current user) click the next button. free datasheet http://www.datasheet-pdf.com/
chapter 2: installation and setup 11 the ready to install screen appears. 7. click the install button to proceed with installation. when the installation is finished, the final installation screen appears. 8. click to finish button to close the installer. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 12 optional. selecting your network if your pc has only one network connection, skip to ?setting up the edgestore? on page 13. if your pc has multiple network connections, you must ensure that the edgestore, nas setup wizard, and smartsync utility are all connected to the same network. the configuration tool performs that function. to make your network selection: 1. from the windows start menu, choose programs , then edge10 nas utility , and then configuration tool . the change system configuration screen appears. 2. from the language dropdown menu, choose the language you prefer. 3. from the scan network interface dropdown menu, choose the ip address for the network where you installed the edgestore. the ip addresses in this menu belong to the network interface cards (nics) in your pc. you must select the nic that is connected to the network where you installed the edgestore. 4. optional. click the ... button to navigate to the browser you want to use as with the edgestore. the default browser appears in the browser path field. change this setting only if you want use a different browser. 5. click the ok button. 6. in the system message, click ok to finish your network selection. free datasheet http://www.datasheet-pdf.com/
chapter 2: installation and setup 13 setting up the edgestore the smartwizard performs the setup procedures on your edgestore. to set up your edgestore: 1. from the windows start menu, choose programs , then edge10 nas utility , then smartwizard . the smartwizard welcome screen appears. 2. from the choosing a language dropdown menu, choose the language you prefer. 3. choose an initiation mode. click the express mode option if all of these conditions apply: ? you have a dhcp server on your network with addresses available. ? you want data protection for your raid volume. ? you want to use date and time settings from your pc. caution the smartwizard will overwrite all existing settings on the edgestore. in most cases, you should only run the smartwizard one time?when you first set up your edgestore. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 14 click the advanced mode option if one or more of these conditions apply: ? you do not have a dhcp server on your network. ? you have a dhcp server but no addresses are available. ? you want to set the ip address manually. ? you want maximum capacity raid 0 volume. ? you want to set date and time manually. the rest of the setup instructions describe express mode. for setup instructions using advanced mode, see ?appendix a: smartwizard advanced mode? on page 135. 4. click next >> to continue. the discovering edge10 nas screen appears. the edgestore is listed as a NAS400 . 5. highlight the edgestore you are initiating, then click next >> to continue. free datasheet http://www.datasheet-pdf.com/
chapter 2: installation and setup 15 the login dialog box appears. 6. type admin into the password field, then click ok . the password is case sensitive. the select a device name screen appears. 7. select a device name (drive letter) to represent the default folder on the edgestore as a network drive on your pc. the list begins with z and goes in reverse alphabetical order. click next >> to continue. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 16 the system message appears. 8. click the yes button to begin the system initiation. the wizard requires several minutes to configure your edgestore, depending on the size of your disk drives. when the wizard is done another system message appears. 9. click ok to finish the system initiation. the wizard creates a raid volume and a default folder called public . if two disk drives are installed in your edgestore, the wizard creates a raid 1 volume. if three or four disk drives are installed, the wizard creates a raid 5 volume. the public folder on the edgestore appears under my computer as a network drive. you can now copy files to and from the folder on the edgestore. free datasheet http://www.datasheet-pdf.com/
chapter 2: installation and setup 17 connecting to easm the edge10 advanced storage manager (easm) software is factory-installed on the edgestore system. easm runs in the browser on your pc. you can access easm: ? directly in your browser. see page 18. ? through smartsync. see page 19. browser support choose one of the following browsers to use with easm: finding the edgestore?s ip address to access the edgestore in your browser, you must know the edgestore?s ip address. use smartsync for this purpose. 1. from the windows start menu, choose programs , then edge10 nas utility , and then smartsync . 2. to open the smartsync window, in the windows application tray (lower right corner of the screen), double-click the smartsync icon. the smartsync screen appears with the server information tab displayed. the ip address of the edgestore shown in the server list. ? internet explorer ? mozilla ?firefox ? netscape navigator ? safari (macos x) smartsync icon ip address of the edgestore detected on the network free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 18 easm in your browser to log into easm in your browser: 1. start your browser. 2. in the browser address field, type in the ip address of the edgestore. see ?finding the edgestore?s ip address? on page 17. note that the ip address shown below is only an example. the ip address you type into your browser will be different. ? easm uses an http connection . . . . . . . . . . . . . . . . . . . . . . .http:// ? enter the edgestore?s ip address . . . . . . . . . . . . . . . .192.168.1.110 together, your entry looks like this: http://192.168.1.110 the easm login screen displays. 3. type the user name and password in the respective fields, then click the login button. the default user name is admin . the default password is admin . the user name and password are case sensitive. for more information about easm, see ?chapter 6: easm? on page 59. free datasheet http://www.datasheet-pdf.com/
chapter 2: installation and setup 19 easm in smartsync to log into easm in smartsync: 1. in the windows application tray (lower right corner of the screen), double-click the smartsync icon (right). smartsync opens with the server information tab displayed. 2. click the open gui button (right). your default browser starts and the easm login screen displays. 3. type the user name and password in the respective fields, then click the login button. the default user name is admin . the default password is admin . the user name and password are case sensitive. for more information about easm, see ?chapter 6: easm? on page 59. smartsync icon open gui button free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 20 shutting down the edgestore to shut down the edgestore, press and hold the power button for five seconds. see figure 3. the system status led turns red, then goes dark. to restart the edgestore, press the power button again. figure 3. press and hold the power button for 5 seconds power button note: this edgestore is shown without the front door. system status led free datasheet http://www.datasheet-pdf.com/
21 chapter 3: connecting to the edgestore ? setting up a network drive on a windows pc (page 21) ? setting up a network drive on a unix or linux pc (page 24) ? setting up a network drive on a macintosh pc (page 27) ? connecting a usb printer to edgestore (page 31) ? setting up the print server on edgestore (page 32) ? setting up windows printing (page 32) ? setting up linux printing (page 34) ? setting up macintosh printing (page 37) ? connecting a usb drive (page 39) ? disconnecting a usb drive (page 42) to copy files to and from a folder on the edgestore, you must make the folder a network drive on your pc. to use the edgestore as a print server, you must connect the usb printer, enable edgestore?s print server, and set up printing on your pc. setting up a network drive on a windows pc you can also use smartsync for this purpose, see ?connecting a network drive? on page 52. if your pc does not have smartsync, use the following procedure to setup a network drive with my network places. to setup a network drive: 1. on the windows desktop, double-click the my network places icon. 2. click the search button in the toolbar. if the search button is not shown, from the view menu, choose toolbars , then standard buttons . 3. in the computer name field, type the ip address of the edgestore and click the search button. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 22 see ?finding the edgestore?s ip address? on page 17. the edgestore appears in the search results list. 4. double-click the edgestore to show the public folder and any other folders you have created. edgestore (NAS400) found on the network free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 23 5. right-click the folder you want and choose map network drive from the dropdown menu. the map network drive dialog box appears. 6. in the map network drive dialog box, choose a drive letter and click the finish button. 7. double-click the my computer icon on your windows desktop. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 24 the folder on the edgestore appears under my computer as a network drive. you can now copy files to and from the folder on the edgestore. setting up a network drive on a unix or linux pc before you can access the edgestore from a unix or linux pc, you must configure the edgestore to communicate with unix and linux. on the windows pc 1. start easm. see ?easm in your browser? on page 18 or ?easm in smartsync? on page 19. 2. in the tree, click the + beside the file & print icon to expand the tree. 3. click the protocol control icon, then click the unix/linux tab. 4. next to service, click the enable option, then click the ok button. edgestore (NAS400) under network drives free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 25 the unix/linux protocol enables unix and linux pcs to connect to edgestore. 5. click the file sharing icon in the tree. 6. click the modify tab. 7. check the unix/linux box, then click the ok button. the unix/linux file sharing enables unix and linux pcs to access folders on the edgestore. in this case, access is given for the public folder. 8. click the sharing setup icon in the tree. 9. click the unix/linux sharing tab. 10. in the new ip address field, type the ip address of the unix/linux pc from which you want to access the edgestore. 11. click the add button. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 26 on the unix/linux pc with command line interface 1. open a terminal window. 2. create a new folder for the edgestore. type mkdir edgestore and press enter. 3. mount the edgestore. type mount 192.168.1.110:/volume1/public/ edgestore and press enter. note that the ip address shown above is only an example. the ip address you type in your terminal window will be different. ?finding the edgestore?s ip address? on page 17. volume1 and public refer to the default volume and folder created during setup.see page 13. if you created another volume or folder, use their names. 4. change to the edgestore directory. type cd /edgestore and press enter. you can now copy files to and from the folder on the edgestore. 5. when you are done with the edgestore, type cd; umount /edgestore and press enter. on the linux pc with graphic desktop this procedure is for a redhat enterprise linux 4 configuration. if you run a different version of linux, you might have to adapt the procedure. see your os documentation. 1. from the applications menu, choose network servers . 2. in the network window, double-click windows network. note that the edgestore (NAS400) is identified by its server name. 3. double-click the edgestore icon. free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 27 4. double-click the folder you want. if this is the first time you accessed this folder, an authentication dialog box opens. 5. type the user name and password in the respective fields, then click the ok button. the default user name is admin . the default password is admin . the user name and password are case sensitive. leave the domain field blank. the folder opens. you can now copy files to and from the folder on the edgestore. setting up a network drive on a macintosh pc before you can access the edgestore from a macintosh (macos x) pc, you must configure the edgestore to communicate with the macos. on the windows pc 1. start easm. see ?easm in your browser? on page 18 or ?easm in smartsync? on page 19. 2. in the tree, click the + beside the file & print icon to expand the tree. 3. click the protocol control icon, then click the macintosh tab. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 28 4. next to service, click the enable option, then click the ok button. the macintosh protocol enables macintosh pcs to connect to edgestore. 5. click the file sharing icon in the tree. 6. click the modify tab. 7. check the macintosh box, then click the ok button. the macintosh file sharing enables macintosh pcs to access folders on the edgestore. in this case, access is given for the public folder. free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 29 on the macintosh pc 1. from the go menu, choose connect to server . 2. in the connect to server dialog box, type afp://192.168.1.110 and click the connect button. note that the ip address shown below is only an example. the ip address you type in the dialog box on your macintosh will be different. see ?finding the edgestore?s ip address? on page 17. click the + button to add this ip address to the favorite servers list. 3. type the user name and password in the respective fields, then click the ok button. the default user name is admin . the default password is admin . the user name and password are case sensitive. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 30 note that the edgestore (NAS400) is identified by its server name. 4. in the select the volumes dialog box, click the folder you want, then click the ok button. 5. in the welcome screen, click the ok button. free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 31 a window opens on the macintosh desktop to access the folder on the edgestore. you can now copy files to and from the folder on the edgestore. connecting a usb printer to edgestore to connect a usb printer to the edgestore: 1. set up your printer according to the printer?s setup guide or user manual . 2. install the printer drivers onto your pc as described in the printer?s setup guide or user manual . 3. attach the usb cable from your printer to one of the usb connections on the back of the edgestore. usb connections free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 32 setting up the print server on edgestore to set up the edgestore?s print server: 1. start easm. see ?easm in your browser? on page 18 or ?easm in smartsync? on page 19. 2. in the tree, on the left side of the easm screen, click the + beside the file & print icon to expand the tree. 3. click the protocol control icon, then click the windows tab. 4. click the enable option button beside services. 5. click the ok button to save your settings. 6. click the printer server tab. 7. click the enable option button beside printer server. 8. click the ok button to save your settings. setting up windows printing to set up printing on a windows pc: 1. on the windows desktop, double-click the my network places icon. 2. click the search button in the toolbar. if the search button is not shown, from the view menu, choose toolbars , then standard buttons . 3. in the computer name field, type the ip address of the edgestore and click the search button in the side bar. see ?finding the edgestore?s ip address? on page 17. the edgestore appears in the search results list. 4. in the computer list, double-click the edgestore to open it. free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 33 if the connect to dialog box appears, type the user name and password in the respective fields, then click the ok button. the default user name is admin . the default password is admin . the user name and password are case sensitive. 5. right-click the usbptr1 icon folder and choose connect... from the dropdown menu. 6. when the warning message about printer drivers appears, click the ok button to continue. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 34 7. in the add printer wizard, click the manufacturer and model name of your usb printer, then click the ok button. 8. in the add printer wizard, click the ok button. 9. to verify printer installation, in the windows start menu, choose settings , then printers and faxes . the printers and faxes screen appears. the usbptr1 is the usb printer on the edgestore. setting up linux printing this procedure is for a redhat enterprise linux 4 configuration. if you run a different version of linux, you might have to adapt the procedure. see your os documentation. 1. from the applications menu, choose system settings , then printing . printer configuration window opens. 2. click the new button. add a new print queue dialog box opens. free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 35 3. click the forward button. 4. in the name field, type a name for the printer, such as nas_printer , a description, and click the forward button. 5. from the select a queue type dropdown menu, choose network windows (smb) . 6. scroll the list and click the triangle icon beside edgestore. note that the edgestore (NAS400) is identified by its server name. usbptr01 appears below the edgestore and represents the usb printer connected to the edgestore. 7. highlight usbptr01 and click the forward button. the authentication dialog box opens. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 36 in the user name and password fields, type admin , then click the ok button. the user name and password are case sensitive. the printer model dialog box opens. 8. from the dropdown menu, choose the manufacturer of your printer. from the model list, highlight the model of your computer. then click the forward button. 9. click the finish button. free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 37 usbptr01 is added to your printer list. setting up macintosh printing to set up printing on a macintosh pc: 1. from the apple menu, choose system preferences . 2. double-click the print & fax icon. 3. click the setup printers button. 4. in the printer list, click the add icon. the printer list displays a new panel. 5. in the new panel, from the popup menus, choose: ? windows printing ? workgroup 6. from the list, highlight the edgestore, then click the choose button. note that the edgestore is listed by its server name. a user name and password dialog box appears. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 38 7. type the user name and password in the respective fields, then click the ok button. the default user name is admin . the default password is admin . the user name and password are case sensitive. the printer list displays a new panel. 8. highlight the usbptr01 in the list. usbprt01 represents the usb printer connected to the edgestore. 9. in the printer model popup menu, choose the make of your printer. 10. in the model name list, choose the model of your printer. free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 39 11. click the add button. usbptr01 is added to your printer list. connecting a usb drive to connect a usb drive to the edgestore, attach the usb cable from your external drive to one of the usb connections on the back of the edgestore. if you have a usb memory stick, attach it directly to one of the usb connections or use a usb cable, whichever is more convenient. the usb drive or memory stick appears as a folder called usbdisk when you create your network drive. see the instructions on the following page. edgestore supports usb drives and memory sticks formatted to fat32 and ext3 file formats. if the edgestore does recognize the usb drive or memory stick, the usb connections free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 40 usbdisk folder does not appear. see ?formatting an external usb drive or memory stick? on page 83. windows pc the usb drive appears as a folder on the edgestore when you create a network drive on a windows pc. follow the procedure ?setting up a network drive on a windows pc? on page 21, but choose the usbdisk folder instead of the public folder. usb drive connected to the edgestore free datasheet http://www.datasheet-pdf.com/
chapter 3: connecting to the edgestore 41 linux pc the usb drive appears as a folder on the edgestore when you create a network drive on a linux pc. follow the procedure ?setting up a network drive on a unix or linux pc? on page 24, but choose the usbdisk folder instead of the public folder. macintosh pc the usb drive appears as a folder on the edgestore when you create a network drive on a macintosh pc. follow the procedure ?setting up a network drive on a macintosh pc? on page 27, but choose the usbdisk folder instead of the public folder. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 42 disconnecting a usb drive to disconnect a usb drive or memory stick from the edgestore: 1. be sure that no files on the usb drive or memory stick are still open. 2. unplug the usb drive or memory stick from the edgestore. the edgestore automatically unmounts the usb drive or memory stick. free datasheet http://www.datasheet-pdf.com/
43 chapter 4: one touch backup ? enabling one touch backup (page 43) ? creating a backup schedule (page 44) ? performing a one touch backup (page 45) ? viewing your backup files (page 46) ? restoring your backup files (page 47) one touch backup enables you to make a quick, automated backup of a selected folder on your pc, at the touch of a button. you can backup the files in a single folder, multiple folders, or your complete hard disk drive. this feature works on the windows pc where you installed the edgestore software. for one touch backup to work, you must: ? enable one touch backup on the edgestore ? create a backup schedule in smartsync enabling one touch backup to enable one touch backup on the edgestore: 1. on the windows pc, start easm. see ?easm in your browser? on page 18 or ?easm in smartsync? on page 19. 2. in the tree, click the + beside the backup icon, then click the client backup icon. caution the edgestore and one touch backup cannot restore a failed boot drive in your pc. however, you can use the edgestore to save your system backup file. see your windows documentation for information about system backups. notes ? windows does not allow smartsync to access protected folders and files. if you want to perform a backup, you must first disable protection on your folders and files. ? if you want to run the windows backup or restore wizard, access the edgestore as a network drive. see ?setting up a network drive on a windows pc? on page 21. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 44 3. on the one touch backup tab, click the enable button for one touch backup services, then click the ok button. creating a backup schedule for each folder you want to backup, you must create a backup schedule. to create a backup schedule in smartsync: 1. on the windows desktop, double-click the smartsync icon (right). 2. in smartsync, click the schedule tab. 3. click the create button. 4. in the backup schedule window, verify the destination. the destination is a letter, typically z, y, or x, which represents a network drive on your pc and a specific folder on the edgestore. 5. in the folder list, click the + icons to expand the tree. the folder list is a representation of the file structure on your pc. 6. click the folder you want to backup. a checkmark appears beside the selected folder. the backup will include the folder you select and all subfolders. 7. click the next >> button. 8. choose a schedule interval by number of hours, daily, or weekly. 9. choose a setting: ? if you chose hours, choose the number of hours from the dropdown menu. smartsync icon free datasheet http://www.datasheet-pdf.com/
chapter 4: one touch backup 45 ? if you chose daily, choose the time of day in the hour (24-hour clock) and minutes dropdown menu. ? if you chose weekly, choose the time of day and day of the week in the hour (24-hour clock), minutes, and day dropdown menus. 10. click the finish button. your backup schedule appears in the schedule tab. performing a one touch backup to perform a one touch backup, press the one touch backup button on the front of the edgestore. one touch backup button free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 46 within moments, the folders you specified are backed up onto the edgestore. the one touch backup function backs up all of the folders on your pc for which you created a backup schedule. viewing your backup files to view your backup files on the edgestore: 1. on the windows pc desktop, double-click the my computer icon. 2. under network drives, double-click the edgestore. 3. on the edgestore, find the backup folder. the backup folder contains the results of the one touch backup from your pc. the subfolders inside the backup folder match the file structure on your pc?s hard disk drive. note the backup folder takes its name from your account name. for example: ? if your account name is ?admin,? the folder name is backup_admin. ? if your account name is ?billy,? the folder name is backup_billy. free datasheet http://www.datasheet-pdf.com/
chapter 4: one touch backup 47 restoring your backup files to restore backup files from the edgestore to your pc: 1. on the windows pc, open smartsync and click the restore tab. 2. in the source field, choose the folder that contains the backup files that you want to restore. in the source field, folders are identified by their network drive names, such as z, y, or x. 3. in the folder list, click the folders that contain the backup files you want to restore. caution the restore function will overwrite files in the destination folder on your pc. if the backup files on the edgestore match the names of the files in the restore location folder on your pc, the restore function will overwrite those files on your pc. if you do not want to overwrite the files on your pc, take one of the following actions: ? move the current files to a different folder on your pc. ? choose a different restore location folder. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 48 in the folder list, folders are identified by their file structure as it was copied from your pc. the lowest folder in the structure is the one that actually contains the files. 4. choose a restore location: ? original location ? the same folder on your pc from which the files were copied for the backup. ? select a restore location ? a folder on your pc that you specify. 5. click the start button. the files are copied from the edgestore to your pc. if you selected a restore location on your pc other than the original, the restore function includes subfolders that match the files structure on your pc?s hard disk drive. free datasheet http://www.datasheet-pdf.com/
49 chapter 5: smartsync ? opening the smartsync window (page 49) ? choosing a language (page 49) ? closing the smartsync window (page 50) ? quitting smartsync (page 50) ? displaying the edgestores on your network (page 50) ? starting easm (page 50) ? connecting a network drive (page 52) ? deleting device (network drive) records (page 53) ? performing a backup (page 53) ? performing a restore (page 55) ? scheduling a backup (page 56) ? setting the default browser for easm (page 58) ? viewing the event log (page 58) after installation, the smartsync utility starts automatically in the background on your windows pc. smartsync does not run on unix, linux, or macintosh pcs. opening the smartsync window to open the smartsync window, in the windows application tray (lower right corner of the screen), double- click the smartsync icon. the smartsync window opens. if the smartsync icon does not appear in the windows application tray, from the windows start menu, choose programs , then edge10 nas utility , and then smartsync . choosing a language to choose a language, click the language menu and choose the language you prefer. smartsync icon free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 50 closing the smartsync window to close the smartsync window, click the x (close) icon at the top right corner of the window. the smartsync window closes but the utility continues to run. to open the smartsync window again, double-click the smartsync icon in the application tray. quitting smartsync to quit smartsync, click the exit button (right). the smartsync utility quits. to restart smartsync, do one of the following actions: ? log out of windows, then log in again. ? from the windows start menu, choose programs , then edge10 nas utility , and then smartsync . displaying the edgestores on your network to display a list of servers (edgestores on your network), open the smartsync window. the smartsync window opens with the server information tab selected. a list of servers appears in the server list on the server information tab. starting easm edge10 advanced storage manager (easm) displays in the default browser. to start the default browser and display easm: 1. open the smartsync window. 2. click the open gui button (right). exit button open gui button free datasheet http://www.datasheet-pdf.com/
chapter 5: smartsync 51 your default browser starts and the easm login screen displays. 3. type the user name and password in the respective fields, then click the login button. the default user name is admin . the default password is admin . the user name and password are case sensitive. for more information about easm, see ?chapter 5: smartsync? on page 49. also see ?setting the default browser for easm? on page 58. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 52 connecting a network drive to access the folders you create on the edgestore, you must make them network drives on your pc. see ?adding a folder? on page 76. to connect a folder on the edgestore as a network drive: 1. open the smartsync window. 2. highlight the edgestore in the server list, then click the connect network drive button (right). the connect network drive dialog box appears. 3. choose the device name and share folder from the dropdown menus. the device name list begins with z and goes in reverse alphabetical order. the share folder list represents the folders you have created on the edgestore. 4. click the ok button. 5. on the windows desktop, double-click the my computer icon. the public folder on the edgestore (NAS400) appears under my computer as a network drive. connect network drive button free datasheet http://www.datasheet-pdf.com/
chapter 5: smartsync 53 deleting device (network drive) records to delete a drive record only affects smartsync. deleting a drive record does not delete your network drive under my computer and it does not affect the data stored in your edgestore?s folders. to delete a device record: 1. open the smartsync window. 2. highlight a server in the server list. 3. click the remove device record button (right). a device list window appears. 4. click the device name that you want to delete, then click the remove button. the device name is removed from the list. 5. click x or the cancel button to close the window. performing a backup a backup copies folders from your pc to the edgestore. also see ?chapter 4: one touch backup? on page 43. to perform a backup of a selected folder: 1. open the smartsync window. 2. highlight a server in the server list. 3. click the backup tab. 4. choose a destination. caution the edgestore and smartsync cannot restore a failed boot drive in your pc. however, you can use the edgestore to save your system backup file. see your windows documentation for information about system backups. note ? windows does not allow smartsync to access protected folders and files. if you want to perform a backup, you must first disable protection on your folders and files. ? if you want to run the windows backup or restore wizard, access the edgestore as a network drive. see ?setting up a network drive on a windows pc? on page 21. remove device record button free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 54 destinations are identified by drive letters and correspond to a specific folder on the edgestore. 5. click the folder you want to backup in the folder list. click the + icon to expand the file tree. a checkmark appears beside the selected folder. the backup will include the folder you choose and all subfolders. 6. do one of the following actions: ? to perform the backup now, click start button. ? to perform the backup later, click the apply button to save your settings. when you are ready perform the backup, click the backup button (right). viewing your backup folders to view your backup folders on the edgestore: 1. on the windows desktop, double-click the my computer icon. 2. under network drives, double-click the edgestore. 3. on the edgestore, find the backup folder. the backup folder contains the results of the one touch backup from your pc. the subfolders inside the backup folder match the file structure on your pc?s hard disk drive. note the backup folder takes its name from your account name. for example: ? if your account name is ?admin,? the folder name is backup_admin. ? if your account name is ?billy,? the folder name is backup_billy. backup button free datasheet http://www.datasheet-pdf.com/
chapter 5: smartsync 55 performing a restore a restore copies folders from the edgestore to your pc. to perform a restore of a chosen folder: 1. open the smartsync window. 2. highlight a server in the server list. 3. click the restore tab. 4. choose a source. sources are identified by drive letters and correspond to a specific folder on the edgestore. 5. choose a restoration location. ? restore to original location ? the files from the edgestore will overwrite the files on our pc ? select a restore location ? the files from the edgestore are saved in a set of folders that match the original file structure from where they were copied 6. optional. if you chose a new restore location, click the browse button (right), navigate to the destination you want, highlight the destination folder, then click the open button to choose the folder. 7. in the folder list, click the folder you want to restore. click the + icon to expand the file tree. a checkmark appears beside the chosen folder. the restore will include the folder you chose and all subfolders. 8. do one of the following actions: ? to perform the restore now, click start button. ? to perform the restore later, click the apply button to save your settings. caution the restore function will overwrite files in the destination folder on your pc. note if you want to run the windows backup or restore wizard, access the edgestore as a network drive. see ?setting up a network drive on a windows pc? on page 21. browse button free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 56 when you are ready perform the backup, click the tools menu and choose restore > start . scheduling a backup a backup copies folders from your pc to the edgestore. to schedule the backup of a selected folder: 1. open the smartsync window. 2. click the schedule tab. 3. click the create button. 4. in the backup schedule window, verify the destination. destinations are identified by drive letters and correspond to a specific folder on the edgestore. 5. in the folder list, click the + icons to expand the tree. the folder list is a representation of the file structure on your pc. 6. click the folder you want to backup. a checkmark appears beside the selected folder. the backup will include the folder you select and all subfolders. 7. click the next >> button. 8. choose a schedule interval by number of hours, daily, or weekly. caution the edgestore and smartsync cannot restore a failed boot drive in your pc. however, you can use the edgestore to save your system backup file. see your windows documentation for information about system backups. note ? windows does not allow smartsync to access protected folders and files. if you want to perform a backup, you must first disable protection on your folders and files. ? if you want to run the windows backup or restore wizard, access the edgestore as a network drive. see ?setting up a network drive on a windows pc? on page 21. free datasheet http://www.datasheet-pdf.com/
chapter 5: smartsync 57 9. choose a setting: ? if you chose hours, choose the number of hours from the dropdown menu. ? if you chose daily, choose the time of day in the hour (24-hour clock) and minutes dropdown menu. ? if you chose weekly, choose the time of day and day of the week in the hour (24-hour clock), minutes, and day dropdown menus. 10. click the finish button. your backup schedule appears in the schedule tab. also see ?chapter 4: one touch backup? on page 43. modifying a backup schedule you can change source folders, time, and day settings for a scheduled backup. to modify a backup schedule: 1. open the smartsync window. 2. click the schedule tab. 3. in the schedule list, highlight the schedule you want to modify. 4. click the modify button. 5. choose the folders you want to backup from the tree, then click next >> . 6. choose the schedule type (hour, daily, weekly). 7. choose the time and day settings. 8. click finish to save your backup settings. deleting a backup schedule to delete a backup schedule: 1. open the smartsync window. 2. click the schedule tab. 3. in the schedule list, highlight the schedule you want to delete. 4. click the delete button. 5. in the confirmation box, click yes . free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 58 setting the default browser for easm to set the default browser for easm: 1. open the smartsync window. 2. click the option menu and choose browser path... the setup browser path dialog box displays. 3. click the ... button, then navigate to the browser?s .exe file. 4. highlight the browser?s .exe file, then click the open button. 5. click the ok button to save your setting. viewing the event log to view the event log: 1. open the smartsync window. 2. click the event log tab. 3. from the type menu, choose the type of events you want to display: ? all ? all events ? info ? information events only ? error ? error events only clearing the event log to clear the event log: 1. open the smartsync window. 2. click the event log tab. 3. click the clear all button. or, click the event menu and choose clear all . saving the event log to a text file to save the event log to a text file: 1. open the smartsync window. 2. click the event log tab. 3. click the save file button (right). 4. in the save dialog box, name the file, navigate to the folder where you want to save the log file, and click the save button. a text file of the event log is saved to the your pc?s hard drive. save file button free datasheet http://www.datasheet-pdf.com/
59 chapter 6: easm ? connecting to easm (below) ? choosing a language (page 62) ? navigating in easm (page 62) ? setting up edgestore with the setup wizard (page 63) ? managing users and groups (page 65) ? managing file & print services (page 70) ? managing raid volumes (page 79) ? managing backups (page 84) ? managing the network connection (page 88) ? making management settings (page 91) ? managing services (page 96) connecting to easm the edge10 advanced storage manager (easm) software is factory-installed on the edgestore system. easm runs in the browser on your pc. you can access easm: ? directly in your browser. see page 60. ? through smartsync. see page 61. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 60 easm in your browser to log into easm in your browser: 1. start your browser. 2. in the browser address field, type in the ip address of the edgestore. see ?finding the edgestore?s ip address? on page 17. note that the ip address shown below is only an example. the ip address you type into your browser will be different. ? easm uses an http connection . . . . . . . . . . . . . . . . . . . . . . .http:// ? enter the edgestore?s ip address . . . . . . . . . . . . . . . .192.168.1.110 together, your entry looks like this: http://192.168.1.110 the easm login screen displays. 3. type the user name and password in the respective fields, then click the login button. the default user name is admin . the default password is admin . the user name and password are case sensitive. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 61 easm in smartsync to log into easm through smartsync: 1. in the windows application tray (lower right corner of the screen), double-click the smartsync icon (right). smartsync opens with the server information tab displayed. 2. click the open gui button (right). your default browser starts and the easm login screen displays. 3. type the user name and password in the respective fields, then click the login button. the default user name is admin . the default password is admin . the user name and password are case sensitive. smartsync icon open gui button free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 62 choosing a language to choose a language, click the language menu in the easm header and choose the language you prefer. navigating in easm the tree is the primary navigation tool in easm. categories of functions listed with a + sign before the icon. icons for specific functions are listed under the categories. click the + sign to show the functions. click the function icons to display their information on the screen. each function has one or more tabs in its screen. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 63 setting up edgestore with the setup wizard if you used the nas setup wizard utility to set up your edgestore, you do not need to run the setup wizard in easm. if you have not yet set up your edgestore: 1. in the tree, click the + beside the wizard icon, then on the setup wizard icon to display the setup wizard screen. 2. click the next button to start the setup wizard. the step 1 screen appears. 3. optional. in the computer name field, enter a name for the edgestore. use only letters, numbers, and the underscore character for the name. 4. under network configuration, choose one of the following options: ? configure using dhcp ? choose this option if your network has a dchp server with addresses available ? configure using specify an ip address ? choose this option if you want to set the ip address and other network setting manually 5. if you chose the configure using specify an ip address option, type the following information in the fields provided: ? ip address ? subnet mask ? default gateway ip address ? primary dns ? secondary dns see your network administrator for help with these settings. 6. click the next button to continue. the step 2 screen appears. 7. optional. type a new administrator password into the new password field. retype the new password into the retype password field. 8. optional. to add a user, click the add new user option button. 9. if you clicked the add new user option button, type a user name and password into the fields provided, then click the add button. 10. click the next button to continue. the step 3 screen appears. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 64 11. check the enable box to the right of the services you plan to use. ? windows ? enables file access from windows pcs. also required to use the edgestore as a print server. ? unix/linux ? enables file access from unix and linux pcs ? macintosh ? enables file access from macintosh pcs ? ftp ? enables file access from pcs using ftp 12. optional. type new names into the workgroup name and computer description fields. 13. click the next button to continue. the step 4 screen appears. you must add at least one folder, which you will access from your pc as a networked drive. 14. to add a folder, click the add new folder option button. 15. type a folder name into the field provided, check the boxes of the services you expect to use with this folder, then click the add button. add more folders as required. 16. click the next button to continue. the step 5 screen appears. if a raid volume already exists on the edgestore, information about the raid volume is shown. to change the raid, you must delete it first, then run the setup wizard again. see ?deleting a raid volume? on page 82. 17. from the raid level dropdown menu, choose the raid level you want for your disk array. see for ?choosing a raid level? on page 106 more information. 18. highlight disk drives in the free disks column and click the >> button to move them to the disks in raid column. 19. click the next button to continue. the finish screen appears. 20. click the finish button to set up your edgestore. the setup process takes several minutes, depending on the size of your disk drives. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 65 managing users and groups this category includes the following topics: ? viewing a list of users (page 65) ? creating a user (page 65) ? changing the administrator?s password (page 65) ? changing a user's password (page 66) ? deleting a user (page 66) ? viewing a list of groups (page 66) ? creating a group (page 67) ? adding members to a group (page 67) ? removing members from a group (page 67) ? deleting a group (page 68) ? viewing quotas (page 68) ? setting quotas (page 68) viewing a list of users to view the list of users: 1. in the tree, click the + beside the users & groups icon. 2. click the user management icon. a list of users appears on the information tab. creating a user you can create up to 512 users. to create or add a new user: 1. in the tree, click the + beside the users & groups icon. 2. click the user management icon. 3. click the create user tab. 4. type a user name in the field provided. 5. type a password into the fields provided. 6. click the ok button. changing the administrator?s password to change the administrator?s password: 1. in the tree, click the + beside the users & groups icon. 2. click the user management icon. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 66 3. click the change password tab. 4. type a new password into the fields provided. 5. click the ok button. if you forget your new password, you reset the edgestore to the default administrator?s password. see ?restoring the default password? on page 124. changing a user's password to change a user?s password: 1. in the tree, click the + beside the users & groups icon. 2. click the user management icon. 3. click the change password tab. 4. from the user name dropdown menu, choose the name of the user whose password you want to change. 5. type a new password into the fields provided. 6. click the ok button. deleting a user you cannot delete the administrator or the guest. to delete any other user: 1. in the tree, click the + beside the users & groups icon. 2. click the user management icon. 3. click the delete user tab. 4. click the option button to the left of the user you want to delete. 5. click the ok button. 6. in the confirmation box, click the ok button. viewing a list of groups groups are composed of users. you can assign permissions to a group, the same as you would do with individual users. to view a list of groups: 1. in the tree, click the + beside the users & groups icon. 2. click the group management icon. a list of groups appears on the information tab. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 67 creating a group groups are composed of users. you can assign permissions to a group, the same as you would do with individual users. you can create up to 256 groups. to create a group: 1. in the tree, click the + beside the users & groups icon. 2. click the group management icon. 3. click the create tab. 4. type a group name in the field provided. 5. click the ok button. adding members to a group you must create a group before you can assign members to it. see ?creating a group? on page 67. to add members to a group: 1. in the tree, click the + beside the users & groups icon. 2. click the group management icon. 3. click the group members tab. 4. from the dropdown menu, choose a group to which you want to add members. 5. highlight users in the users column and click the >> button to move them to the members column. 6. click the ok button. removing members from a group to remove members from a group: 1. in the tree, click the + beside the users & groups icon. 2. click the group management icon. 3. click the group members tab. 4. from the dropdown menu, choose a group from which you want to remove members 5. highlight users in the members column and click the << button to move them to the users column. 6. click the ok button. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 68 deleting a group you must remove all members from the group before you can delete the group. see ?removing members from a group? on page 67. to delete a group: 1. in the tree, click the + beside the users & groups icon. 2. click the group management icon. 3. click the delete tab. 4. click the option button next to the group you want to delete. 5. click the ok button. viewing quotas quotas are portions of storage space that you assign to each user or group. to view a quota: 1. in the tree, click the + beside the users & groups icon. 2. click the quota icon. a list of users and groups, and the following data appear on the screen: ? currently assigned quotas ? free space ? used space setting quotas quotas are portions of storage space that you assign to each user or group. assigning quotas enables you to control how much storage space each user or group can access. by default, each user and group is assigned an unlimited quota, meaning that any one user or group can access the entire storage space. in the quota screen, the names of groups are preceded with a @ symbol. to set a quota: 1. in the tree, click the + beside the users & groups icon. 2. click the quota icon. 3. click the settings tab. 4. highlight the user or group whose quota you want to assign. 5. click one of the following options: ? unlimited ? limited quota free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 69 6. if you chose limited quota, type a number into the field provided. this number represents how many mb of data the user or group can access. 7. click the ok button. note if you set different size quotas for the user and the group, edgestore will use the smaller quota. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 70 managing file & print services this category includes the following topics: ? setting up windows access (page 70) ? setting up unix/linux access (page 71) ? setting up for macintosh access (page 72) ? setting up for ftp access (page 73) ? setting up your print server (page 74) ? setting up your dlna server (page 74) ? viewing a list of folders (page 75) ? modifying folder services (page 75) ? adding a folder (page 76) ? deleting a folder (page 76) ? setting up windows sharing for a folder (page 77) ? setting up unix and linux sharing for a folder (page 77) ? setting up ftp sharing for a folder (page 78) setting up windows access follow this procedure to set up access from a windows pc: 1. in the tree, click the + beside the file & print icon. 2. click the protocol control icon. 3. click the windows tab. 4. click the enable option button beside services. 5. optional. type a new computer description into the field provided. 6. choose the option button to make the edgestore a member of: ? an active directory (ad) domain ?a workgroup note: if you join an ad domain, you automatically disable your nis domain settings. see ?setting up unix/linux access? on page 71. 7. optional. if you chose an ad domain, enter the following in the fields provided: ? domain name ? domain controller ? administrator name ? administrator password see your network administrator for help with this information. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 71 8. optional. if you chose an workgroup, enter the workgroup name into the field provided: see your network administrator for help with this information. 9. click the ok button to save your settings. 10. in the tree, click the + beside the sharing setup icon. 11. click the windows sharing tab. 12. choose a folder from the folder name dropdown menu. 13. in the user/group list, highlight the name of a user or group. group names are preceded by the @ character. 14. under permissions, choose a permission level for this user or group: ? deny access ? read only ? read and write 15. click the ok button to save your settings. you can now access the folder you chose from a windows pc. see ?chapter 3: connecting to the edgestore? on page 21 for information about the settings that you must make on your pc. setting up unix/linux access follow this procedure to set up access from a unix or linux pc: 1. in the tree, click the + beside the file & print icon. 2. click the protocol control icon. 3. click the unix/linux tab. 4. click the enable option button beside services. 5. optional. if you want to join a nis domain, click the nis domain option button. note: if you join an nis domain, you automatically disable your ad domain settings. see ?setting up windows access? on page 70. 6. optional. if you chose to join a nis domain, enter the domain name into the field provided. see your network administrator for help with this information. note windows support is only through smb and cifs protocols. edgestore supports the recycle bin feature. when you delete a file, the file is moved to the recycle bin, a hidden folder in the share folder. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 72 7. click the ok button to save your settings. 8. in the tree, click the + beside the file sharing icon. 9. click the modify tab. 10. from the folder name dropdown menu, choose the folder you want to access. 11. check the unix/linux box. 12. click the ok button to save your settings. 13. in the tree, click the + beside the sharing setup icon. 14. click the unix/linux sharing tab. 15. choose a folder from the folder name dropdown menu. 16. in the new ip address field, type the ip address of the unix or linux pc from which you will access this folder, then click the add button. you must designate the ip addresses for each folder individually. you can have up to 256 ip addresses for all of your folders. 17. click the ok button to save your settings. you can now access the folder you chose from a unix or linux pc. see ?chapter 3: connecting to the edgestore? on page 21 for information about the settings that you must make on your pc. setting up for macintosh access follow this procedure to set up access from a macintosh pc: 1. in the tree, click the + beside the file & print icon. 2. click the protocol control icon. 3. click the macintosh tab. 4. click the enable option button beside services. 5. click the ok button to save your settings. 6. in the tree, click the + beside the file sharing icon. 7. click the modify tab. 8. from the folder name dropdown menu, choose the folder you want to access. 9. check the macintosh box. 10. click the ok button to save your settings. you can now access the specified folder from a macintosh pc. see ?chapter 3: connecting to the edgestore? on page 21 for information about the settings that you must make on your pc. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 73 setting up for ftp access follow this procedure to set up ftp access for your folders: 1. in the tree, click the + beside the file & print icon. 2. click the protocol control icon. 3. click the ftp sharing tab. 4. click the enable option button beside services. 5. type a command port number into the field provided. port 21 is typically used for the command port. 6. optional. if you want to specify a range of passive data port numbers, type those numbers into the fields provided. the port range is 1024 to 65535. be sure the port numbers you enter are enabled on your firewall and server. in active mode, the ftp server uses port 20 for the data port. 7. optional. if your ftp client uses double-byte characters but does not support unicode, choose your ftp client?s encoding from the client coding type dropdown menu. choose from: ? unicode ?shift-jis ?gb2312 ?big5 8. click the ok button to save your settings. 9. in the tree, click the + beside the file sharing icon. 10. click the modify tab. 11. from the folder name dropdown menu, choose the folder you want to access. 12. check the ftp box. 13. click the ok button to save your settings. you can now access the specified folder from your pc using ftp. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 74 setting up your print server follow this procedure to set up the edgestore as a printer server: 1. in the tree, click the + beside the file & print icon. 2. click the protocol control icon. 3. click the windows tab. 4. click the enable option button beside services. 5. click the ok button to save your settings. 6. click the printer server tab. 7. click the enable option button beside printer server. 8. click the ok button to save your settings. setting up your dlna server the digital living network alliance (dlna) service enables the universal plug- and-play (upnp) protocol, so your edgestore can function as a digital media server (dms). when your dlna service is enabled, you can connect your dlna control unit or upnp client on the network where the edgestore is connected, and use the edgestore to play image, audio, and av media. you must install the optional dlna plug-in before you can make this setting and use the upnp protocol. see ?installing application plug-ins? on page 145. follow this procedure to set up the edgestore as a dlna server: 1. in the tree, click the + beside the file & print icon. 2. click the protocol control icon. 3. click the dlna server tab. 4. click the enable option button beside services. 5. click the ok button to save your settings. notes ? the printer server tab also verifies that your usb printer is connected and online. if you do not see your printer on the printer server tab, take the necessary action to connect and power the printer. see ?connecting a usb printer to edgestore? on page 31. ? the software driver for your printer must be installed on your pc before you can print from the pc. see the printer?s setup guide or user manual . free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 75 the media content directory is /volume1/pluginapp/dlna/. this is a shared folder created when you install the dlna plug-in. the directory has three sub- directories: picture, music, and video. with the dlna plug-in, edgestore supports these media formats: ? picture ? bmp, gif, jpg, jpeg, png, tif ? music ? mp3, pcm, wma ? video ? avi, mpg, mpeg, wmv, tts, vob viewing a list of folders a folder is the entity that appears as a network drive on your pc. to view the list of folders: 1. in the tree, click the + beside the file & print icon. 2. click the file sharing icon. a list of current folders appears in the information tab. modifying folder services services enable different types of pcs to access your folders. use this function to add or remove a service for a specific folder. to modify the services on a folder: 1. in the tree, click the + beside the file & print icon. 2. click the file sharing icon. 3. click the modify tab 4. from the volume dropdown menu, choose the raid volume containing the folder you want to modify. 5. from the folder name dropdown menu, choose the folder you want to modify. 6. check the boxes beside the services you want to use. 7. click the ok button. if the service you want is off, see: ?setting up windows access? on page 70 ?setting up unix/linux access? on page 71 ?setting up for macintosh access? on page 72 ?setting up for ftp access? on page 73 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 76 adding a folder a folder is the entity that appears as a network drive on your pc. to add a folder: 1. in the tree, click the + beside the file & print icon. 2. click the file sharing icon. 3. click the create tab. 4. from the volume dropdown menu, choose the raid volume in which you want to create a new folder. 5. in the folder name field, type a name for your new folder. 6. check the boxes beside the services you want to use. 7. click the ok button. to access the new folder from a windows pc, see ?setting up windows sharing for a folder? on page 77. to access the new folder from a unix or linux pc, see ?setting up unix and linux sharing for a folder? on page 77. to make the folder a network drive on your pc, see ?chapter 3: connecting to the edgestore? on page 21. deleting a folder to delete a folder: 1. in the tree, click the + beside the file & print icon. 2. click the file sharing icon. 3. click the remove tab 4. click the option button beside the folder you want to delete. 5. click the ok button. 6. in the confirmation box, click the ok button to confirm. caution when you delete a folder, you delete all the data saved in the folder. back up any important data before you delete a folder. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 77 setting up windows sharing for a folder windows sharing assigns user access the folders on your edgestore. by default all users and groups have read-only access. to set up windows sharing for a folder: 1. in the tree, click the + beside the file & print icon. 2. click the sharing setup icon. 3. click the windows sharing tab. 4. from the volume dropdown menu, choose the raid volume containing the folder you want to modify. 5. from the folder name dropdown menu, choose the folder you want to modify. 6. in the permission list, click the option button for one of the following permissions for each group and user: ? deny access ? read only ? read and write 7. click the ok button. be sure the windows service is running for this folder. see ?setting up windows access? on page 70. setting up unix and linux sharing for a folder unix and linux sharing designates which unix and linux pcs can access the folders on your edgestore. you specify a unix or linux pc by its ip address. you can add up to 256 ip addresses for all of your folders. you must designate the ip addresses for each folder individually. to set up unix and linux sharing for a folder: 1. in the tree, click the + beside the file & print icon. 2. click the sharing setup icon in the tree. 3. click the unix/linux sharing tab. 4. from the volume dropdown menu, choose the raid volume containing the folder you want to modify. 5. from the folder name dropdown menu, choose the folder you want to modify. 6. in the new ip address field, type the iip address of the unix or linux pc from which you will access this folder. 7. click the add button. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 78 be sure the unix/linux service is running for this folder. see ?setting up unix/linux access? on page 71. setting up ftp sharing for a folder ftp sharing assigns user access the folders on your edgestore. by default all users and groups have read-only access. to set up ftp sharing for a folder: 1. in the tree, click the + beside the file & print icon. 2. click the sharing setup icon. 3. click the ftp sharing tab. 4. from the volume dropdown menu, choose the raid volume containing the folder you want to modify. 5. from the folder name dropdown menu, choose the folder you want to modify. 6. in the permission list, click the option button for one of the following permissions for each group and user: ? deny access ? read only ? read and write 7. click the ok button. be sure the ftp service is running for this folder. see ?setting up for ftp access? on page 73. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 79 managing raid volumes this category includes the following topics: ? viewing raid volume status (page 79) ? viewing disk drive information (page 80) ? creating a raid volume (page 80) ? designating a spare drive (page 81) ? migrating a raid volume (page 81) ? deleting a raid volume (page 82) ? viewing an external usb drive or memory stick (page 83) ? formatting an external usb drive or memory stick (page 83) viewing raid volume status raid status refers to the disk drives on your edgestore and how they are arranged into a raid volume. to view the status of your raid volume: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. the raid status tab displays the current raid system and its status: ? raid name ? the name of your raid, automatically assigned when it was created ? raid level ? raid 0, 1, 5, or 10, specified when it was created ? capacity ? data capacity of the raid volume in gb ? raid status ? functional is normal. critical means a disk drive has failed. offline means you cannot access your data. critical and offline raids require you to take corrective action. see ?replacing a failed disk drive? on page 113. ? action status ? idle is normal. rebuilding means the raid volume is being rebuilt after a disk drive failure. migrating means the raid volume is adding a disk drive or changing raid levels. ? background activity ? none is normal. running means a background activity is in progress. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 80 viewing disk drive information to view information about a disk drive: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. the raid status tab displays the current raid system and its status. 3. in the disk list, double-click a disk drive icon. the disk drive information displays under disk status. creating a raid volume on edgestore, the term raid volume refers to one or more disk drives working together as a raid logical drive. you can also use a usb disk to create a raid volume. see ?viewing an external usb drive or memory stick? on page 83. you must have unassigned disk drives in your edgestore to create a new raid. to create a new raid volume: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. 3. click the create tab. 4. from the raid level dropdown menu, choose the raid level you prefer for your disk array. see ?choosing a raid level? on page 106 for more information. 5. highlight disk drives in the free disks column and click the >> button to move them to the disks in raid column. 6. click the ok button. the raid volume is created and formatting begins. formatting requires several minutes, depending on the size of your disk drives. after formatting is done, you must create folders on your raid volume. see ?adding a folder? on page 76. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 81 designating a spare drive if you have an unassigned disk drive, you can assign it as a spare drive. for more information, see ?spare drive? on page 107 and ?automatic rebuilding? on page 108. to assign a spare drive: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. 3. click the create tab. 4. from the raid level dropdown menu, choose spare disk . 5. highlight a disk drive in the free disks column and click the >> button to move it to the disks in raid column. 6. click the ok button. migrating a raid volume to migrate a raid volume means to change its raid level or to add disk drives. see ?raid volume migration? on page 109 for more information. to migrate a raid volume: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. 3. click the modify tab. 4. from the current volume dropdown menu, choose the raid volume which you want to modify. 5. in the migrate to raid level dropdown menu, choose the target raid level. 6. to add disk drives, highlight disk drives in the free disks column and click the >> button to move them to the disks in raid column. 7. click the ok button. the raid volume is modified as you directed. migration requires several minutes, depending on the type of modification taking place and the size of your disk drives. during the modification, your raid volume and all of the folders on it are fully accessible. after the migration is completed, you must extend the file system in order to use the storage space you have added. you can extend the file system immediately or wait until later. 8. click the file system management icon. 9. in the file system status tab, click the extend file system button. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 82 deleting a raid volume to delete a raid volume: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. 3. click the delete tab. 4. click the option button beside the raid volume you want to delete. 5. click the ok button. 6. in the confirmation box, type yes into the field provided, then click the ok button. after a raid volume is deleted, the edgestore reboots automatically. when the edgestore is fully booted: ? the system status led turns green (right) ? the buzzer beeps one time (if the buzzer is enabled) 7. close your browser then restart the browser to access easm. caution when you delete a raid volume, you delete all the folders in the raid volume and all the data saved in the folders. back up any important data before you delete a raid volume. note you cannot delete a raid volume while a background activity is running, such as migration or rebuild. wait until these activities are completed. system status led free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 83 viewing an external usb drive or memory stick to view a usb drive or memory stick attached to the edgestore: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. the usb drive or memory stick appears as a usb external disk 3. click the file system management icon. the usb drive or memory stick appears as a volume called usbdisk. you do not create a raid volume or folders with the usb drive or memory stick as you would with the disk drives installed in the edgestore enclosure. with the usb drive or memory stick connected to the edgestore, create a network drive on your pc and choose the usb disk as the folder. then you can access the usb drive or memory stick from your pc. see ?chapter 3: connecting to the edgestore? on page 21 for more information. formatting an external usb drive or memory stick this option only appears when edgestore does not recognize the file system on the usb drive or memory stick. to format a usb drive or memory stick: 1. attach the usb drive or memory stick to one of the usb ports on the back of the edgestore. 2. in the tree, click the + beside the raid & file system icon. 3. click the file system management icon. 4. on the file system status tab, highlight the usb drive. 5. from the format file system type dropdown menu, choose a file system: ? fat 32 ? use for windows, linux, and macintosh pcs, and edgestore ? ext3 ? use for unix and linux pcs, and edgestore 6. click the format usb disk button. 7. in the confirmation box, type yes , then click the ok button. formatting requires several minutes, depending on the size of your usb drive or memory stick. caution when you format a usb drive or memory stick, you delete all the data saved on it. back up any important data before you format. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 84 managing backups this category includes the following topics: ? viewing a list of snapshot backups (page 84) ? setting up a snapshot backup (page 84) ? scheduling a snapshot backup (page 85) ? recovering snapshot backups (page 85) ? viewing the nas replication schedule (page 86) ? setting up nas replication (page 86) ? enabling one touch backup (page 87) viewing a list of snapshot backups to view the list of snapshot backups: 1. in the tree, click the + beside the backup icon. 2. click the snapshot backup icon. the current list of snapshots displays on the information tab. setting up a snapshot backup to setup a snapshot backup: 1. in the tree, click the + beside the backup icon. 2. click the snapshot backup icon. 3. click the setup tab. 4. from the volume dropdown menu, choose the raid volume you want to backup. 5. next to snapshot status, click the enable option. 6. in the reserve capacity dropdown menu, choose a portion in gb of the raid volume you want to reserve for snapshots. 7. click the ok button. 8. in the confirmation box, type yes into the filed provided than click the ok button. the snapshot backup settings are applied. the process takes a few moments. click the schedule tab for scheduling options. caution setting up a snapshot will delete all existing snapshots. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 85 scheduling a snapshot backup to schedule a snapshot backup: 1. in the tree, click the + beside the backup icon. 2. click the snapshot backup icon. 3. click the schedule tab. 4. click the option you want from the schedule type list. ? disable ? no snapshots will be taken. ? do it at once ? snapshots will be taken now, one time only. ? time interval by hour ? snapshots will be taken at the hourly interval you choose from the dropdown menu. ? daily ? snapshots will be taken at the time of day you choose from the dropdown menus. ? weekly ? snapshots will be taken on the day of the week, at the time of day you choose from the dropdown menus. 5. as needed, make your choices from the dropdown menus. 6. click the ok button. the new backup schedule is applied. if you have not yet made your snapshot settings, click the setup tab and make them now. recovering snapshot backups the snapshot recovery feature has two functions: ? use a snapshot to restore the data volume (volume1 or volumex) to an earlier point in time. ? export a snapshot to the share folder. the recovered snapshot volume is read-only. to recover a snapshot backup: 1. in the tree, click the + beside the backup icon. 2. click the snapshot backup icon. 3. click the recovery tab. 4. click the option button beside the timestamp and volume that you want to recover or export. 5. do one of the following actions: ? to restore the data volume using the snapshot, click the ok button. ? to export the snapshot to the share folder, click the export button. edgestore performs the action you specified. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 86 viewing the nas replication schedule nas replication is a feature that uses one edgestore to backup the data on another edgestore. the two edgestore systems must be on the same network. to view the nas replication schedule: 1. in the tree, click the + beside the backup icon. 2. click the nas replication icon. the current schedule displays on the information tab. ?role: standalone ? no backup server was specified primary server ? this edgestore is the primary, the other edgestore is the backup backup server ? this edgestore is the backup, the other edgestore is the primary ? primary or backup server ? the ip address of the other edgestore on the network. ? schedule ? replication schedule in number of hours, daily or weekly. appears on the primary server. setting up nas replication to set up nas replication: 1. in the tree, click the + beside the backup icon. 2. click the nas replication icon. 3. click the setup tab. 4. under settings, click the option button to assign a role to this edgestore: ? standalone ? use this option when you only have one edgestore on your network. this is the default setting and it disables nas replication. ? primary ? this edgestore is the primary and the other edgestore is the backup server. ? backup server ? the other edgestore is the primary and this edgestore is the backup server. 5. optional. if you chose primary or backup server, type the ip address of the other edgestore on your network. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 87 6. under schedule, click the option button for the schedule type you want: ? disable ? disables nas replication ? do it at once ? performs a nas replication when you click the ok button. ? time interval by hour ? set an hourly interval for nas replications to happen. ? daily ? sets the time of day when the nas replications happen. ? weekly ? sets the time of day and day of the week when the nas replications happen. 7. click the ok button. enabling one touch backup one touch backup is a feature that enables you to backup specified folders from your pc to the edgestore by pressing a button on the front of the edgestore. to enable one touch backup: 1. in the tree, click the + beside the backup icon. 2. click the client backup icon. 3. in the one touch backup tab, click the enable option. 4. click the ok button. to disable one touch backup, click the disable option, then click the ok button. see ?chapter 4: one touch backup? on page 43. one touch backup button free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 88 managing the network connection this category includes the following topics: ? viewing network setup information (page 88) ? making network settings (page 88) ? working with jumbo frames (page 89) ? setting up your ddns service (page 90) viewing network setup information to view network setup information: 1. in the tree, click the + beside the network icon. 2. click the network setup icon. the current network setup for this edgestore displays on the information tab: ? computer name ? ip address ? subnet mask ? default gateway ip address ? primary domain name server ip address ? secondary domain name server ip address to change these settings, click the setup tab. making network settings to make network settings: 3. in the tree, click the + beside the network icon. 4. click the network setup icon. 5. click the setup tab. 6. optional. type a name for the edgestore in the computer name field. 7. click an option button to choose an internet protocol option: ? obtain an ip address automatically ? choose this option to let your dhcp server make the network settings. ? specify an ip address ? choose this option if you want to make your network settings manually. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 89 8. optional. if you chose specify an ip address , enter the following settings in the fields provided: ? ip address ? subnet mask ? default gateway ip address ? primary domain name server ip address ? secondary domain name server ip address see your network administrator for help in making these settings. 9. click the ok button to save your settings. working with jumbo frames the term jumbo frame refers to a frame on a local area network that is larger than the standard 1518 byte size. edgestore supports jumbo frames up to 9000 bytes. on edgestore, the frame size setting is called maximum transmission unit (mtu). the default mtu or frame is 1500 bytes. this setting is appropriate for most users. see your network administrator before you change this setting. to make frame size settings: 1. in the tree, click the + beside the network icon. 2. click the network setup icon. 3. click the jumbo frame tab. 4. from the mtu dropdown menu, choose the maximum mtu or frame size: ? 1500 bytes (default) ? 4000 bytes ? 7000 bytes ? 9000 bytes 5. click the ok button to save your setting. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 90 setting up your ddns service the dynamic domain name server service enables you to keep the same domain name even though your ip address changes. you must register with dynamic network services in order to obtain your domain name, user name, and password. follow this procedure to set up the ddns service: 1. in the tree, click the + beside the network icon. 2. click the network setup icon. 3. click the ddns tab. 4. click the enable option button beside services. 5. enter your domain name in the ddns name field. 6. enter your user name and password in the fields provided. 7. click the ok button to save your settings. your ddns service is now active. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 91 making management settings this category includes the following topics: ? viewing service status (page 91) ? viewing the event log (page 92) ? setting up smtp authentication (page 92) ? viewing the email alert list (page 93) ? adding an email alert recipient (page 93) ? deleting an email alert recipient (page 93) ? upgrading the system firmware (page 93) ? enabling and disabling the buzzer (page 94) ? viewing ups status (page 94) ? setting up a ups (page 95) viewing service status the edgestore runs services to enable pcs to access the folders on the edgestore and to work as a print server. to view service status: 1. in the tree, click the + beside the management icon. 2. click the service status icon. the status of each service displays on the information tab. ? on ? the service is running. ? off ? the service is not running. 3. if the service you want is off, click the enable button to the right of the service. also see: ?setting up windows access? on page 70 ?setting up unix/linux access? on page 71 ?setting up for macintosh access? on page 72 ?setting up for ftp access? on page 73 ?setting up your print server? on page 74 ?setting up your dlna server? on page 74 ?setting up your ddns service? on page 90 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 92 viewing the event log the event log keeps a log of the 20 most recent events on the edgestore. you can use this information to review your actions and to diagnose problems. to view the event log: 1. in the tree, click the + beside the management icon. 2. click the event log icon. a list of the 20 most recent events displays on the event log tab. events are ranked in severity as information, warning, and error. setting up smtp authentication in order to set up email alerts over a network, you must enable the smtp service, specify a smtp server, and in most cases, supply authentication information. see your network administrator for help with these settings. to set up smtp authentication: 1. in the tree, click the + beside the management icon. 2. click the mail alert icon. 3. click the setup tab. 4. next to service, click the enable option button. 5. in the smtp server field, type the ip address or the dns name of your smtp server. 6. in the from field, the sender?s email address that you want to appear in the alert messages. 7. next to smtp authentication: ? click the yes option button to enable authentication. ? click the no option button to disable authentication. note that most smtp servers require authentication. 8. if you enabled authentication, to the following: ? in the user name field, type the mail server account name. ? in the password field, type the password of the mailer server account. 9. click the ok button. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 93 viewing the email alert list the edgestore will send alerts via email to the recipients you designate. to view a list of email alert recipients: 1. in the tree, click the + beside the management icon. 2. click the mail alert icon. the list of recipients displays on the mail list tab. see ?checking your email inbox? on page 124 for an example of an email alert message. adding an email alert recipient you can have up to 32 email alert recipients. to add an email alert recipient: 1. in the tree, click the + beside the management icon. 2. click the mail alert icon. 3. click the add tab. 4. in the e-mail address field, type the recipient?s email address. 5. click the ok button. deleting an email alert recipient to delete an email alert recipient: 6. in the tree, click the + beside the management icon. 7. click the mail alert icon. 8. click the delete tab. 9. click the option button beside the e-mail address you want to delete. 10. click the ok button. 11. in the confirmation box, click the ok button. upgrading the system firmware see ?upgrading the firmware? on page 143. installing an application plug-in see ?installing application plug-ins? on page 145. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 94 enabling and disabling the buzzer the edgestore has a buzzer that sounds when the edgestore is finished booting and when a problem is detected. the buzzer is enabled by default. edge10 recommends that you leave the buzzer enabled. to disable the buzzer: 1. in the tree, click the + beside the management icon. 2. click the buzzer icon. 3. click the disable option button. 4. click the ok button. click the enable option button, then click the ok button to enable the buzzer. viewing ups status if you have an apc uninterruptable power supply (ups) attached to the edgestore, you can check its status in easm. to view ups status: 1. in the tree, click the + beside the management icon. 2. click the apc ups icon. the information tab displays the status of the ups. if there is no ups connected or recognized, the status field reports ?no ups.? free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 95 setting up a ups to set up a ups: 1. attach the apc ups to one of the edgestore?s usb ports. 2. in the tree, click the + beside the management icon. 3. click the apc ups icon. 4. click the setup tab. the setup tab enables you to tell the edgestore how and when to shutdown after a power failure. click the option button beside the shutdown option you want: ? disable (the edgestore will continue to run until the ups battery is depleted) ? shutdown when the ups reaches a set percentage of reserve power ? shutdown when the ups reaches a set number of minutes of remaining runtime ? shutdown after running on the ups batteries for a set number of minutes 5. optional. if you chose battery percentage, type a percentage amount in the % field. 6. optional. if you chose remaining runtime or running on batteries, type the number of minutes into the mins. field. 7. click the ok button. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 96 managing services this category includes the following topics: ? setting system date and time (page 96) ? running the network time protocol (page 96) ? viewing the results of ntp synchronization (page 97) ? rebooting the edgestore (page 97) ? shutting down the edgestore (page 98) ? restarting the edgestore (page 98) ? locating the edgestore (page 98) ? viewing system information (page 99) ? viewing enclosure information (page 99) setting system date and time 1. to set the date and time on the edgestore: in the tree, click the + beside the system icon. 2. click the date / time icon. 3. click the setup tab. 4. from the dropdown menus, choose the time and date values. 5. click the ok button. running the network time protocol you can use the network time protocol (ntp) to set the system date and time on your edgestore to synchronize itself with an external time server. to run the network time protocol: 1. in the tree, click the + beside the system icon. 2. click the date / time icon. 3. click the time zone tab. 4. from the dropdown menu, choose the time zone for your location. 5. click the ok button. 6. click the ntp tab. 7. in the time server field, type the url of the time server you want to use. url time.nist.gov is the default. free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 97 8. under schedule, choose one of the options: ? disable ? disables ntp synchronization ? do it at once ? performs a synchronization when you click the ok button. ? time interval by hour ? set an hourly interval for a synchronization to happen. ? daily ? sets the time of day when the synchronization happens. ? weekly ? sets the time of day and day of the week when the synchronization happens. 9. click the ok button. viewing the results of ntp synchronization to view the results of an ntp synchronization: 1. in the tree, click the + beside the system icon. 2. click the date / time icon. 3. click the ntp tab. the results of the latest synchronization are displayed: ? last synchronization time ? time and date of the last synchronization ? last synchronization result ? ok means success rebooting the edgestore normally you will only need to reboot the edgestore is after a firmware upgrade or a plug-in installation. see ?upgrading the firmware? on page 143. during the reboot, none of your folders will be accessible from your networked pcs. to reboot the edgestore: 1. in the tree, click the + beside the system icon. 2. click the reboot / shutdown icon. 3. click the reboot option. 4. click the ok button. 5. in the confirmation box, click the ok button. the reboot runs automatically. when the edgestore is fully booted: ? the system status led turns green (right) ? the buzzer beeps one time (if the buzzer is enabled) see ?enabling and disabling the buzzer? on page 94. system status led free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 98 shutting down the edgestore the only time you need to shut down the edgestore is to replace the disk drive cooling fan or the power supply. see ?appendix b: maintenance? on page 143. during and after the shutdown, none of your folders will be accessible from your networked pcs. using easm to shut down the edgestore: 1. in the tree, click the + beside the system icon. 2. click the reboot / shutdown icon. 3. click the shutdown option. 4. click the ok button. 5. in the confirmation box, click the ok button. directly to shut down the edgestore, press and hold the power button for five seconds. the system status led turns red, then goes dark (right). restarting the edgestore to restart the edgestore after a shutdown, press the power button on the front of the edgestore chassis (right). when the edgestore is fully booted: ? the system status led turns green (right) ? the buzzer beeps one time (if the buzzer is enabled) see ?enabling and disabling the buzzer? on page 94. locating the edgestore if your edgestore in is on a rack with other equipment and you need to locate it quickly, this function will assist you. to locate the edgestore: 1. in the tree, click the + beside the system icon. 2. click the system information icon. 3. click the system information tab. 4. click the locate button. the edgestore?s buzzer beeps three times and the system status led blinks three times (right). power button system status led system status led free datasheet http://www.datasheet-pdf.com/
chapter 6: easm 99 viewing system information to view system information: 1. in the tree, click the + beside the system icon. 2. click the system information icon. 3. click the system information tab. system information includes: ? operating system ? embedded linux ? firmware version ? changes when you upgrade the firmware. see ?upgrading the firmware? on page 143 ? cpu model ? mpc 8343 ? network adapter ? gigabit ethernet ? network flow ? inflow and outflow speeds in bits per second viewing enclosure information to view enclosure information: 1. in the tree, click the + beside the system icon. 2. click the system information icon. 3. click the enclosure information tab. enclosure information includes: ? cpu temperature ? system temperature ?system fan speed ? power status 5v ? power status 12v ? power status 3.3v if any values are out of specification, see ?checking enclosure status in easm? on page 120. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 100 free datasheet http://www.datasheet-pdf.com/
101 chapter 7: technology background ? introduction to raid (below) ? choosing a raid level (page 106) ? spare drive (page 107) ? partition and format (page 108) ? raid volume migration (page 109) introduction to raid raid (redundant array of independent disks) allows multiple disk drives to be combined together into a raid volume . you create a raid volume on your edgestore when you perform the setup procedure, either in the nas setup wizard or the easm setup wizard. the benefits of a raid can include: ? higher data transfer rates for increased server performance ? increased overall storage capacity for a single volume ? data redundancy/fault tolerance for ensuring continuous system operation in the event of a disk drive failure different raid levels use different organizational models and have varying benefits. also see ?choosing a raid level? on page 106. the following outline breaks down the properties for each raid level supported on the edgestore: free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 102 raid 0 ? stripe when a raid volume is striped, the read and write blocks of data are interleaved between the sectors of multiple disk drives. performance is increased, since the workload is balanced between drives or ?members? that form the raid volume. identical drives are recommended for performance as well as data storage efficiency. figure 1. raid 0 striping interleaves data across multiple drives the raid volume?s data capacity equals the capacity of the smallest disk drive times the number of disk drives. for example, one 100 gb and three 120 gb drives will form a 400 gb (4 x 100 gb) raid volume instead of 460 gb. if disk drives of different capacities are used, there will also be unused capacity on the larger drives. because raid 0 does not offer fault tolerance, meaning that you cannot recover your data after a disk drive failure, edge10 does not recommend a raid 0 volume for your edgestore. raid 0 volumes on edgestore consist of one or more disk drives. data stripe disk drives free datasheet http://www.datasheet-pdf.com/
chapter 7: technology background 103 raid 1 ? mirror when a raid volume is mirrored, identical data is written to a pair of disk drives, while reads are performed in parallel. the reads are performed using elevator seek and load balancing techniques where the workload is distributed in the most efficient manner. whichever drive is not busy and is positioned closer to the data will be accessed first. with raid 1, if one disk drive fails or has errors, the other mirrored disk drive continues to function. this is called fault tolerance. moreover, if a spare disk drive is present, the spare drive will be used as the replacement drive and data will begin to be mirrored to it from the remaining good drive. figure 2. raid 1 mirrors identical data to two drives the raid volume?s data capacity equals the smaller disk drive. for example, a 100 gb disk drive and a 120 gb disk drive have a combined capacity of 100 gb in a mirrored raid volume. if disk drives of different capacities are used, there will also be unused capacity on the larger drive. raid 1 volumes on edgestore consist of two disk drives. if you want a mirrored raid volume with more than two disk drives, see ?raid 10 ? mirror / stripe? on page 105. 1 2 3 4 1 2 3 4 data mirror disk drives free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 104 raid 5 ? block striping with distributed parity raid 5 organizes block data and parity data across the disk drives. generally, raid level 5 tends to exhibit lower random write performance due to the heavy workload of parity recalculation for each i/o. raid 5 works well for file, database, application and web servers. figure 3. raid 5 stripes all drives with data and parity information the capacity of a raid 5 volume equals the smallest disk drive times the number of disk drives, minus one. hence, a raid 5 volume with four 100 gb disk drives will have a capacity of 300 gb. a raid volume with two 120 gb disk drives and one 100 gb disk drive will have a capacity of 200 gb. raid 5 is generally considered to be the most versatile raid level. raid 5 requires a minimum of three disk drives. data blocks distributed parity disk drives free datasheet http://www.datasheet-pdf.com/
chapter 7: technology background 105 raid 10 ? mirror / stripe mirror/stripe combines both of the raid 0 and raid 1 types. raid 10 can increase performance by reading and writing data in parallel while protecting data with duplication. at least four disk drives are needed for raid 10 to be installed. with a four-disk-drive raid volume, one drive pair is mirrored together then striped over a second drive pair. figure 4. raid 10 takes a data mirror on one drive pair and stripes it over two drive pairs the data capacity raid 10 volume equals the capacity of the smallest disk drive times the number of disk drives, divided by two. in some cases, raid 10 offers double fault tolerance, depending on which disk drives fail. raid 10 volumes on edgestore consist of four disk drives. because all of the available disk drives are used for the raid volume, you cannot set up a spare drive with raid 10. data stripe data mirror disk drives free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 106 choosing a raid level there are several issues to consider when choosing the raid level for your volume. the following discussion summarizes some advantages, disadvantages and applications for each choice. raid 0 recommended applications for raid 0: ?image editing ? pre-press applications ? any application requiring high bandwidth raid 1 recommended applications for raid 1: ? accounting/financial ?payroll ? any application requiring very high availability advantages disadvantages implements a striped disk raid volume, the data is broken down into blocks and each block is written to a separate disk drive i/o performance is greatly improved by spreading the i/o load across many channels and drives no parity calculation overhead is involved not a true raid because it is not fault- tolerant the failure of just one drive will result in all data in an raid volume being lost should not be used in mission critical environments advantages disadvantages simplest raid storage subsystem design can increase read performance by processing data requests in parallel since the same data resides on two different drives very high disk overhead - uses only 50% of total capacity free datasheet http://www.datasheet-pdf.com/
chapter 7: technology background 107 raid 5 recommended applications for raid 5: ? file and application servers ? www, e-mail, and news servers ? intranet servers raid 10 recommended applications for raid 10: ? imaging applications ? database servers ? general fileserver spare drive a spare is a disk drive that has been designated to replace a failed disk drive in a raid volume. in the event of the failure of a disk drive within a raid 1 or three- drive raid 5 volume, the spare drive is activated as a member of the raid volume to replace a disk drive that has failed. a spare drive cannot replace the failed drive in a raid 0 volume because of the way in which data is written to the disk drives under raid 0. a spare drive is not available for a raid 10 volume because raid 10 requires all four disk drives in the edgestore enclosure. however, when you replace the failed disk drive, the edgestore will automatically rebuild the raid volume using the new disk drive. advantages disadvantages high read data transaction rate medium write data transaction rate good aggregate transfer rate most versatile raid level disk failure has a medium impact on throughput advantages disadvantages implemented as a mirrored raid volume whose segments are raid 0 raid volumes high i/o rates are achieved thanks to multiple stripe segments very high disk overhead ? uses only 50% of total capacity free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 108 you must designate a disk drive as a spare. by default, and unassigned disk drive is free. use easm to designate the free disk drive as a spare. see maintaining a spare drive is a good precaution to protect your raid volume integrity in the event of disk drive failure. automatic rebuilding when a disk drive in your raid 1, 5, or 10 volume fails, and a replacement disk drive becomes available, the raid volume will rebuild itself to the new disk drive automatically. for raid 1 and three-drive raid 5 volumes, you can designate a spare drive. if a spare drive is present when the raid volume experiences a disk drive failure, the rebuild will start automatically using the spare drive. for raid 1, raid 5, and raid 10 vo lumes without a spare drive, the raid volume will begin to rebuild itself automatically when you remove the failed disk drive and install a new disk drive. a raid 0 volume cannot be rebuilt because of the way in which data is written to the disk drives under raid 0. even if there is a designated spare drive, rebuilding is not possible for raid 0 volumes. partition and format when you create a raid volume on edgestore, the raid volume is automatically partitioned and formatted for you. to use your raid volume, you must cr eate folders on the raid volume and assign services to those folders according to your requirements. edgestore provides file services for windows, unix/linux and macintosh, so all of those pcs can access the folders on the edgestore, even though each pc might have a different file system. free datasheet http://www.datasheet-pdf.com/
chapter 7: technology background 109 raid volume migration migration is the process of: ? changing the raid level ? adding disk drives but keeping the same raid level in the migration process, the existing raid volume is called the source . the proposed raid volume is called the target . each target raid volume has certain requirements and they are different for each raid level. you must meet all of the requirements in order to successfully migrate a raid volume. in most cases, you must add one or more disk drives during the migration process. you can never reduce the number of disk drives. while the migration is running, you can still access the folders on your raid volume and the data they contain. the tables below shows the migration options for a source raid volume according to its raid level. the available target raid levels are shown with their requirements. raid 0 a raid 0 source volume can migrate to the following target raid levels: raid 1 a raid 1 source volume can migrate to the following target raid levels: target requirements raid 0 add disk drives. raid 1 2 disk drives only. only a 1-drive raid 0 can migrate to raid 1. add 1 disk drive. raid 5 3 disk drives minimum. at least 1 more disk drive than the raid 0 raid volume. target requirements raid 0 can use same number of disk drives. raid 5 3 disk drives minimum. at least 1 more disk drive than the raid 1 raid volume. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 110 raid 5 a raid 5 source volume can migrate to the following target raid levels: raid 10 a raid 10 source volume cannot migrate or add more disk drives. target requirements raid 0 can use same number of disk drives. raid 5 add a disk drive. free datasheet http://www.datasheet-pdf.com/
111 chapter 8: troubleshooting ? responding to an audible alarm (page 111) ? checking the system status led (page 112) ? checking disk status leds (page 112) ? replacing a failed disk drive (page 113) ? checking raid volume status in easm (page 113) ? checking file system status in easm (page 115) ? checking the event log in easm (page 116) ? checking enclosure status in easm (page 120) ? resolving connections with smartsync (page 121) ? solving network connection problems (page 123) ? restoring the default password (page 124) ? resolving a windows firewall issue (page 125) this chapter deals problems you might encounter with your edgestore and how to resolve them. also see ?frequently asked questions? on page 127. responding to an audible alarm the edgestore has two beep patterns ? single beep, not repeated ? the edgestore is online ? two beeps, continuously repeated ? the edgestore reports a problem when you boot or reboot the edgestore, and the buzzer is enabled, the buzzer sounds one time to indicate that the edgestore is online. if you hear the two-beep pattern, check the following items: ? system status led (see below) ? drive status led (see page 112) ? raid volume status in easm (see page 113) ? file system status in easm (see page 115) ? enclosure status in easm (see page 120) ? event log in easm (see page 116) ? your email inbox (see page 124) free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 112 checking the system status led the edgestore system status led (see figure 1.) reports the condition of the enclosure fan and power supply: ? green ? normal enclosure function ? amber ? there is a problem with the fan or power supply ? red ? the fan, power supply, or file system has failed if your edgestore is configured to work with a ups, it will continue to run after a power supply failure. checking disk status leds the disk status leds (see figure 1.) report the condition of the disk drives: ? green ? normal disk drive function ? amber ? rebuilding to this disk drive ? red ? failed disk drive ? dark ? no disk drive is installed see ?replacing a failed disk drive? on page 113. figure 1. edgestore disk and system status leds disk status led system status led free datasheet http://www.datasheet-pdf.com/
chapter 8: troubleshooting 113 replacing a failed disk drive if a disk drive fails, the disk status led is red. see figure 1. if the disk drive belongs to a raid volume, the volume goes critical or offline. see ?checking raid volume status in easm? on page 113. replace the failed disk drive with a new disk drive of the same or slightly greater capacity. you do not have to power down the edgestore. 1. open the edgestore?s front door. 2. pull out the drive carrier with the failed drive. 3. remove the failed disk drive from the drive carrier. 4. install a new disk drive into the carrier. 5. place the carrier with the new disk drive back into the open slot in the edgestore. if the failed drive belonged to a raid volume, the raid volume will begin rebuilding as soon as the new drive is installed. during the rebuild, the disk status led show amber. when the rebuild is finished, the disk status led turns green. if the replacement drive is free, that is, not assigned to a raid volume or as a spare, the disk status led remains dark after you install the new drive. checking raid volume status in easm to view raid volume status: 1. start easm. see ?easm in your browser? on page 60. or see ?easm in smartsync? on page 61. 2. in the tree, click the + beside the raid & file system icon. 3. click the raid management icon. the status is displayed in the raid status tab. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 114 figure 2. easm reports a critical raid volume edgestore responds to a critical raid volume how the edgestore responds to a critical raid volume depends on the raid level of your volume and whether you have a spare drive available: ? for a raid 1 volume or a three-drive raid 5 volume, if a spare drive is available, the raid volume begins rebuilding itself automatically. ? for raid 1, 5, and 10 volumes, when no spare drive is available, you must replace the failed disk drive. the raid volume will begin rebuilding itself when you install the new disk drive. see ?replacing a failed disk drive? on page 113. ? raid 0 volumes go offline after a disk drive failure. a raid 0 volume cannot be rebuilt. all data on the volume is lost. additional details about rebuilds ? the rebuild takes several minutes, depending on the size of your disk drives. ? during a rebuild, you can access your folders on the edgestore. ? when you replace the failed disk drive with a new disk drive, the new disk drive becomes a free drive. responding to an invalid raid volume the edgestore considers a raid volume invalid when the raid volume was created by a different edgestore. however, the raid volume itself remains functional and the data on it is safe. this condition could happen when you: ? move the disk drives from one edgestore to a different edgestore. ? remove the disk drives in order to send your edgestore for service. raid critical icon rebuild in progress free datasheet http://www.datasheet-pdf.com/
chapter 8: troubleshooting 115 when the edgestore?s memory does not recognize the raid volume, so easm displays the raid volume as invalid. see figure 3. use the recover function to validate the raid volume. the recover tab is only active when an invalid raid volume is present and can be recovered. figure 3. an invalid raid volume in easm using the recover function to validate the raid volume: 1. in the tree, click the + beside the raid & file system icon. 2. click the raid management icon. 3. click the recover tab. 4. on the recover tab, click the option button beside the invalid raid volume. 5. click the ok button. the edgestore will reboot itself to update its configuration and recognize the raid volume. checking file system status in easm typically the first indication of a problem with the edgestore?s file system is when your network drive becomes unavailable. you might also see the message, ?file system contains errors. please check.? when you click the icons under the file & print menu. important running the recover function might erase some or all of your edgestore settings. if that condition happens, run the nas setup wizard. see ?setting up the edgestore? on page 13. raid critical icon recover tab is active raid volume is functional free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 116 to view file system status: 1. start easm. see ?easm in your browser? on page 60. or see ?easm in smartsync? on page 61. 2. in the tree, click the + beside the raid & file system icon. 3. click the file system management icon. 4. look for the raid volume icon on the file system status tab. if the raid volume icon is critical (has a yellow !), the file system contains errors and you must rebuild the file system. see below. rebuilding the file system to rebuild a file system: 1. in the tree, click the + beside the raid & file system icon. 2. click the file system management icon. 3. in the file system status tab, click the raid volume critical icon to display the rebuild file system button. 4. click the rebuild file system button. 5. in the confirmation box, type yes into the field provided, then click the ok button. checking the event log in easm to view the event log in easm: to check enclosure status: 1. start easm. see ?easm in your browser? on page 60. or see ?easm in smartsync? on page 61. 2. in the tree, click the + beside the management icon. 3. click the event log icon. the event log displays. see figure 4. caution when you rebuild a file system, you delete all the folders in the raid volume and all the data saved in the folders. free datasheet http://www.datasheet-pdf.com/
chapter 8: troubleshooting 117 figure 4. the easm event log 4. check the event log for reports of disk drive failure or other problems. responding to events all events are reported in the event log. most events are simply reports that the edgestore is responding to your commands. many events are also reported via email. the edgestore?s buzzer sounds for serious events that require your attention. a list of event categories is shown below: ? file system (page 117) ? nas replication (page 118) ? snapshots (page 118) ? system (enclosure) (page 118) ? disk drives (page 119) ? raid volumes (page 119) reported event corrective action file system file system of volume x content errors! check the system before continuing. the file system has a problem. reboot the edgestore and check file system again. if the event appears again, the file system has crashed. rebuild the file system. see page 116. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 118 file system capacity usage of volume x is over 90%. reduce the number or size of the files or expand the volume size. see ?migrating a raid volume? on page 81. file system capacity usage of volume x is 100%. rebuilding file system... the file system is being rebuild by user action. nas replication nas replication is completed. nas replication has finished. normal. system is busy. nas replication is abort! the raid volume is currently formatting, rebuilding, or migrating. wait until this process is done. then try the replication again. system is doing another replication. nas replication is abort! the smarstor is currently doing a replication. wait until the current replication is done. then try the second replication again. nas replication is failed! there is a failed network connection between the two edgestores. correct the problem and try again. see page 123. snapshots the snapshot capacity usage which timestamp is [date and time] of volume x is over 90%. move the snapshot volume to another storage location. or delete the snapshot and then create a new one. see page 84. system is busy. snapshot creation was aborted! the raid volume is currently formatting, rebuilding, or migrating. wait until this process is done. then try the snapshot again. system is creating another snapshot. snapshot creation was aborted! the smarstor is currently doing a snapshot. wait until the current snapshot is done. then try the second snapshot again. system (enclosure) system is starting to work. normal. system is rebooting. system is shutting down. reported event corrective action free datasheet http://www.datasheet-pdf.com/
chapter 8: troubleshooting 119 system was shut down abnormally. the edgestore shut down incorrectly the last time. see ?shutting down the edgestore? on page 98. cpu temperature is higher than 50c/122f. system will shut down. allow the edgestore to cool for several minutes. then restart the edgestore and check system temperature and fan operation. see page 120. be sure there is adequate air circulation around the edgestore. system temperature is higher than 50c/122f. system will shut down. system fan speed is lower than 1500 rpm. check the system before continuing. replace the fan. see page 146. ac power failure. system will shut down. restore the ac power. then restart the edgestore. see ?connecting the power? on page 8. disk drives task x timeout on disk y at lba [address] a lba error. check the disk drives. see page 112. check the raid volume. see page 113. replace the disk drive or rebuild the raid volume as needed. task x disk error on disk y at lba [address] with status z s.m.a.r.t threshold exceeded on disk x check the disk drives. see page 112. replace the failed drive. see page 113. bsl update on disk x at lba [address] bad sector on a disk drive. check the disk drives. see page 112. replace the disk drive if it continues to receive bsl updates. bsl log disk x at lba [address] cleared check the disk drives. see page 112. delete spare disk delete a spare drive. normal. raid volumes create [raid name, raid level and x number of disk drives] create a raid volume. normal. delete raid x delete a raid volume. normal. migration or rebuilding on array x started. raid volume migration or rebuild has started. normal. migration or rebuilding on array x at y%. progress report on raid volume migration or rebuild. normal. reported event corrective action free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 120 checking enclosure status in easm to check enclosure status: 1. start easm. see ?easm in your browser? on page 60. or see ?easm in smartsync? on page 61. 2. in the tree, click the + beside the system icon. 3. click the system information icon. 4. click the enclosure information tab. see figure 5. migration or rebuilding on array x paused at y%. raid volume migration or rebuild was paused temporarily by user action. migration or rebuilding on array x resumed at y%. raid volume migration or rebuild was paused and then resumed by user action. migration or rebuilding on array x completed. raid volume migration or rebuild has finished. normal. migration or rebuilding on array x aborted at y% raid volume migration or rebuild was aborted (stopped) by user action. migration or rebuilding on array x aborted at y% because of error. raid volume migration or rebuild has aborted (stopped) because of an error. check the disk drives. see page 112. check the raid volume. see page 113. raid status: ?offline?. the NAS400 x volume y is offline. check the disk drives. see page 112. replace the failed drive. see page 113. create a new raid volume. see page 80. raid status: ?critical?. the NAS400 x volume y is not functioning correctly. check the disk drives. see page 112. replace the failed drive. see page 113. the raid volume will rebuild automatically. raid x had some errors. formatting was aborted! check the disk drives. see page 112. replace the failed drive. see page 113. reported event corrective action free datasheet http://www.datasheet-pdf.com/
chapter 8: troubleshooting 121 figure 5. the enclosure information tab with malfunctions shown the corrective action you take depends on the nature of the problem: ? if cpu temperature is above specification: ? be sure there is adequate air flow around the edgestore. ? be sure the ambient temperature is below 35c (95f). ? check the fan speed. ? if the fan speed is below specification, contact technical support. see page 130. ? if any power status is out-of-specification, contact technical support. see page 130. resolving connections with smartsync the smartsync utility is designed to detect the edgestore on your network. if smartsync does not detect your edgestore, check the following items: ? be sure the edgestore is powered up and fully booted. the power button and system status led should be green. see figure 6. ? be sure the edgestore is properly connected to your network. the ethernet activity led should be green or blinking green. see figure 6. if the ethernet activity led is dark, see ?solving network connection problems? on page 123. ? be sure that smartsync is looking on the same network where you connected the edgestore. overheat icon failed fan icon out-of-spec power icon free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 122 figure 6. power button, system status and ethernet activity leds multiple network connections if your pc has multiple network connections, you must verify that smartsync is looking on the network where the edgestore is installed: 1. open smartsync. in the windows application tray (lower right corner of the screen), double-click the smartsync icon. 2. from the option menu, choose scan network interface . 3. in the dropdown menu, choose the ip address of the network interface card connected to the network where you installed the edgestore. see figure 7. figure 7. scan network interface in smartsync power button ethernet activity led system status led smartsync icon free datasheet http://www.datasheet-pdf.com/
chapter 8: troubleshooting 123 solving network connection problems most network connection problems are the result of poor connections. when the edgestore is fully booted and connected to the network, the ethernet activity led indicates status and activity: ? green ? network link is properly connected ? flashing green ? network activity ? dark ? no connection see figure 6. if your edgestore is connected to your network but the ethernet activity led on your edgestore is dark, check the following items: ? verify that the switch, hub, or facility network service connection that you are using is operational. switches and hubs have leds that light when there is a connection and flash when there is activity. network service connections generally do not have leds to verify whether they actually are connected to the network. see your network administrator for assistance. ? be sure the network cable is firmly attached to the edgestore network connector at one end and to the network switch, hub, or facility network connection at the other. ? if the cable connections are good, remove the existing network cable and install a known-good network cable. if you know your network devices are working properly and you know that your network cable is good, but the ethernet activity led remains dark, see ?contacting technical support? on page 130. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 124 checking your email inbox if you enabled mail alert in easm, the edgestore will send you an email message when a problem arises. look for a message from ?root.? figure 8. email message from the edgestore. see ?adding an email alert recipient? on page 93 for more information about email alerts. restoring the default password normally, you change your password in easm. see ?changing the administrator?s password? on page 65. if you changed the password and then forgot the new password, you can reset the edgestore to the default password: admin . use a straightened paper clip or the tip of a ball-point pen as a reset tool. to reset the administrator?s password: 1. verify that the edgestore is fully booted. 2. insert your reset tool into the reset button hole on the back of the edgestore. see figure 9. 3. press and hold the reset button for eight seconds, until the system status led flashes three times. the administrator?s password is now reset to admin . free datasheet http://www.datasheet-pdf.com/
chapter 8: troubleshooting 125 figure 9. reset button and system status led resolving a windows firewall issue if you a running a personal firewall on your windows pc, the firewall might prevent the you from accessing the edgestore over your network. follow this procedure to add an exception for the edgestore: 1. from the windows start menu, choose settings , then network connections . the network connections window opens. 2. right-click local area connection and choose properties from the popup menu. the local area connection properties dialog box opens. 3. click the advanced tab. 4. click the settings button. reset button system status led free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 126 the windows firewall dialog box opens. 5. click the advanced tab. 6. under network connection setting, click the settings button. the advanced settings dialog box opens. 7. click the add button. the service settings dialog box opens. 8. in the description of service field, type edge10 nas utility . 9. in the name or ip address field, type the ip address of the edgestore. see ?finding the edgestore?s ip address? on page 17. 10. in the external port field, type 49152 . 11. click the udp option button. 12. in the internal port field, type 49152 . 13. click the ok button. figure 10.windows firewall advanced service settings 14. click the ok buttons in the advanced settings, windows firewall, and local area connection properties dialog boxes. free datasheet http://www.datasheet-pdf.com/
127 chapter 9: support ? frequently asked questions (below) ? contacting technical support (page 130) ? limited warranty (page 131) ? returning product for repair (page 133) frequently asked questions also see ?chapter 8: troubleshooting? on page 111. the edgestore worked ok until i turned it off. when i turned it on again, my windows network drive connection no longer works. when you powered up the edgestore, the dhcp server assigned a different ip address to the edgestore. here are two possible solutions: ? you may be able to reset the edgestore?s ip address manually. see ?connecting a network drive? on page 52 or ?making network settings? on page 88. note that changing the edgestore?s ip address may cause an ip address conflict on your network. check with your network administrator before taking this action. ? if you cannot restore the previous ip address, you must create new network drives and printer connections. see ?chapter 3: connecting to the edgestore? on page 21. when i start windows, a message displays that says, ?could not reconnect all network drives.? the edgestore reconnects to your pc shortly after windows starts. in most cases, the edgestore network drives will be available by the time you click them. the nas setup wizard cannot access the edgestore over the network. if you a running a personal firewall on your windows pc, the firewall might prevent you from accessing folders on the edgestore. you must do one of the following actions: ? disable the firewall ? add an exception for the edgestore see ?resolving a windows firewall issue? on page 125. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 128 i tried to connect my edgestore as a network drive using smartsync, but windows displayed an error message. there might be an ip address conflict between the edgestore and another device on your network. see your network administrator for assistance. i cannot log into the edgestore with through the ad domain. be sure you use a ?domain name\user name? when you log into the edgestore using smb, ftp, or afp. you must use the ?\? character. many ftp clients do not support a space in the domain name or user name. also, the edgestore does not support a user home directory. how does the edgestore integrate into an nis domain? if the nis domain account or group name is the same as the edgestore, the edgestore will apply them to its account or group. if the edgestore joins a nis domain, joining only affects the nfs service and quota settings. the other services are not affected. how are non-ascii folder file names displayed? the edgestore supports unicode, so you can use non-ascii characters in your folder names. windows 98 and me do not support unicode, so they cannot display your folder names properly. but you can still access your folders. i tried to copy a windows shortcut to my network drive, but an error message says there is not enough free disk space. normally, you can copy a windows shortcut to a network drive. however, if the network drive is a usb drive or memory stick with fat32 file format, the edgestore might not recognize the shortcut and prevent you from copying it. if this situation occurs, choose a different folder in which to copy the shortcut. does edgestore support a usb drive or memory stick with fat16 file format? no. if you attach the fat16 usb drive or memory stick to edgestore, you can see the files on it. but if you attempt to copy files to the drive or memory stick, windows might display a disk full message. how do i remove a usb drive or memory stick from the edgestore? be sure that no files on the usb drive or memory stick are still open. then unplug the usb drive or memory stick from the edgestore. the edgestore automatically unmounts the usb drive or memory stick. free datasheet http://www.datasheet-pdf.com/
chapter 9: support 129 can i do a one touch backup or a regular backup on a protected folder or file on my windows pc? no. windows does not allow smartsync to access protected folders and files. if you want to perform a backup, you must first disable protection on your folders and files. which ftp clients are compatible with the edgestore?s ftp server? edge10 recommends ftp clients that support unicode, such as filezilla or smart ftp for windows, filezilla for linux, and transmit v3.5.5 for macintosh. if your ftp client does not support unicode, you have two choices: ? use only ascii characters to name your shared folders. ? set your edgestore for double-byte character encoding. see page 73. i cannot find the dlna server tab under protocol control in easm. you must download and install the dlna plug-in on your edgestore to access this feature. see ?installing application plug-ins? on page 145. can i move the disk drives from one edgestore to a different edgestore? yes. however, to access the raid volume on the new edgestore, you must run the recover function. when edgestore?s memory does not match the raid volume on the disk drives, the raid volume is considered invalid and the recover function becomes available. see ?responding to an invalid raid volume? on page 114. i set up email alert recipients but they never receive any messages. in most cases, you must setup smtp authentication in order for your alert messages to pass your smtp server. see ?setting up smtp authentication? on page 92. can edgestore handle jumbo frames? yes. but you must set the maximum frame size in easm. see ?working with jumbo frames? on page 89. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 130 contacting technical support if you decide to contact us, please have the following information available: ? product model and serial number ? bios, firmware, and driver version numbers ? a description of the problem / situation ? system configuration information, including: motherboard and cpu type, hard drive model(s), sas/sata/ata/atapi drives & devices, and other controllers. technical support visit the edge10 web site at www.edge10.com . edge10 corporation limited manchester business park, 3000 aviator way, manchester. m22 5tg. uk. tel: + 44 (0) 871 855 01 10 fax: + 44 (0) 871 855 21 53 uk warranty centre +44 (0) 70 77 810 210 (customer help line) free datasheet http://www.datasheet-pdf.com/
chapter 9: support 131 limited warranty edge10 corporation limited (?edge10?) warrants that for three (3) years from the time of the delivery of the product to the original end user: a) the product will conform to edge10?s specifications; b) the product will be free from defects in material and workmanship under normal use and service. this warranty: a) applies only to products which are new and in cartons on the date of purchase; b) is not transferable; c) is valid only when accompanied by a copy of the original purchase invoice. d) is not valid on spare parts, fans, and power supplies this warranty shall not apply to defects resulting from: a) improper or inadequate maintenance, or unauthorized modification(s), performed by the end user; b) operation outside the environmental specifications for the product; c) accident, misuse, negligence, misapplication, abuse, natural or personal disaster, or maintenance by anyone other than a edge10 or a edge10-authorized service center. disclaimer of other warranties this warranty covers only parts and labor, and excludes coverage on software items as expressly set above. except as expressly set forth above, edge10 disclaims any warranties, expressed or implied, by statute or otherwise, regarding the product, including, without limitation, any warranties for fitness for any purpose, quality, merchantability, non-infringement, or otherwise. edge10 makes no warranty or representation concerning the suitability of any product for use with any other item. you assume full responsibility for selecting products and for ensuring that the products selected are compatible and appropriate for use with other goods with which they will be used. edge10 does not warrant that any product is free from errors or that it will interface without problems with your computer system. it is your responsibility to back up or otherwise save important data before installing any product and continue to back up your important data regularly. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 132 no other document, statement or representation may be relied on to vary the terms of this limited warranty. edge10?s sole responsibility with respect to any product is to do one of the following: a) replace the product with a conforming unit of the same or superior product; b) repair the product. edge10 shall not be liable for the cost of procuring substitute goods, services, lost profits, unrealized savings, equipment damage, costs of recovering, reprogramming, or reproducing of programs or data stored in or used with the products, or for any other general, special, consequential, indirect, incidental, or punitive damages, whether in contract, tort, or otherwise, notwithstanding the failure of the essential purpose of the foregoing remedy and regardless of whether edge10 has been advised of the possibility of such damages. edge10 is not an insurer. if you desire insurance against such damage, you must obtain insurance from another party. some states do not allow the exclusion or limitation of incidental or consequential damages for consumer products, so the above limitation may not apply to you. this warranty gives specific legal rights, and you may also have other rights that vary from state to state. this limited warranty is governed by the state of california. your responsibilities you are responsible for determining whether the product is appropriate for your use and will interface with your equipment without malfunction or damage. you are also responsible for backing up your data before installing any product and for regularly backing up your data after installing the product. edge10 is not liable for any damage to equipment or data loss resulting from the use of any product. free datasheet http://www.datasheet-pdf.com/
chapter 9: support 133 returning product for repair if you suspect a product is not working properly, or if you have any questions about your product, contact technical support (see page 130), making sure to provide the following information: ? product model and serial number (required) ? return shipping address ? daytime phone number ? description of the problem ? copy of the original purchase invoice the technician will assist you in determining whether the product requires repair. if the product needs repair, technical support provide you with the necessary instructions. you are responsible for the cost of insurance and shipment of the product to edge10. note that damage incurred due to improper transport or packaging is not covered under the limited warranty. when repairing returned product(s), edge10 may replace defective parts with new or reconditioned parts, or replace the entire unit with a new or reconditioned unit. in the event of a replacement, the replacement unit will be under warranty for the remainder of the original warranty term from purchase date, or 30 days, whichever is longer. edge10 will pay for standard return shipping charges only. you will be required to pay for any additional shipping options (such as express shipping). free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 134 free datasheet http://www.datasheet-pdf.com/
135 appendix a: smartwizard advanced mode the smartwizard performs the setup procedures on your edgestore. to set up your edgestore: 1. from the windows start menu, choose programs , then edge10 nas utility , and then smartwizard . the smartwizard welcome screen appears. 2. from the choosing a language dropdown menu, choose the language you prefer. 3. choose an initiation mode. click the express mode option if all of these conditions apply: ? you have a dhcp server on your network with addresses available. ? you want data protection for your disk array. ? you want to use date and time settings from your pc. express mode is recommended for most users. click the advanced mode option if one or more of these conditions apply: ? you do not have a dhcp server on your network. ? you have a dhcp server but no addresses are available. ? you want to set the ip address manually. ? you want maximum capacity (raid 0) for your disk array. ? you want to set date and time manually. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 136 the rest of the setup instructions describe advanced mode. for setup instructions using express mode, see ?setting up the edgestore? on page 13. 4. click next >> to continue. the discovering edge10 nas screen appears. 5. highlight the edgestore you are initiating, then click next >> to continue. the login dialog box appears. 6. type admin into the password field, then click ok . the administrator and password are case sensitive. the time zone, date and time screen appears. free datasheet http://www.datasheet-pdf.com/
appendix a: smartwizard advanced mode 137 7. from the dropdown menus, choose your: ? time zone ?year ?month ?date ? time in hours (24 hour clock), minutes and seconds click next >> to continue. the making network settings screen appears. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 138 8. in the making network settings screen, choose one of the following: ? obtain network settings automatically... ? if you have a dhcp server on your network with ip addresses available, and you want the edgestore to obtain the network settings from the dhcp server, choose this option. ? make network settings manually ? if you do not have a dhcp server, there are no addresses available, or you prefer to make your own network settings, choose this option click next >> to continue. if you chose the automatic option, the protecting your data screen appears. skip to step 10. if you chose the manual option, the making network settings manually screen appears. important if your dhcp server assigns the ip address to the edgestore, and you later restart the edgestore, the dhcp server might assign a different ip address. if the edgestore?s ip address changes, your existing network drives and printer connections will no longer work. you must then create new network drives and printer connections. free datasheet http://www.datasheet-pdf.com/
appendix a: smartwizard advanced mode 139 9. type your entries into the fields provided: ? computer name ? the edgestore?s server name of your choice ? ip address ? subnet mask ? default gateway ? primary dns ? secondary dns click next >> to continue. the protecting your data screen appears. note see your network administrator for help in making these settings. edge10 suggests that you set the first three octets of the edgestore?s ip address to match the first three octets of your pc?s ip address. after initiation, you can change your network settings in smartsync or in easm. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 140 10. in the protecting your data screen: ? check the create new storage box if you are setting up the edgestore for the first time. the wizard creates a raid array, a default volume, and a default folder called public . ? uncheck the create new storage box if you already have a raid and file system on your edgestore. by unchecking the box the wizard will leave your existing file system intact. if you checked the create new storage box, choose one of the following options: ? data protection ? creates a fault-tolerant raid volume on your edgestore. if two disk drives are installed, the wizard creates a raid 1 volume. if three or four disk drives are installed, the wizard creates a raid 5 volume. ? maximum capacity ? creates a raid 0 volume on your edgestore. the full combined capacity of the disk drives will be available for data caution if you check the create new storage box, the wizard will delete all existing data and folders on the edgestore. free datasheet http://www.datasheet-pdf.com/
appendix a: smartwizard advanced mode 141 storage but there will be no fault tolerance to protect your data if one of the disk drives fails. click next >> to continue. the assigning a network device name screen appears. 11. select a device name or drive letter to represent the edgestore as a network drive. the list begins with z and goes in reverse alphabetical order. click next >> to continue. the reviewing your settings screen appears. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 142 12. review your settings and click finish to begin the system initiation. a system message appears. 13. in the system message, click ok to finish the system initiation. the wizard creates a raid volume and a default folder called public . if two disk drives are installed in your edgestore, the wizard creates a raid 1 volume. if three or four disk drives are installed, the wizard creates a raid 5 volume. the public folder on the edgestore appears under my computer as a network drive. you can now copy files to and from the folder on the edgestore. to access this folder from other pcs, see ?chapter 3: connecting to the edgestore? on page 21. to create additional raid volumes and folders, see ?adding a folder? on page 76. free datasheet http://www.datasheet-pdf.com/
143 appendix b: maintenance ? upgrading the firmware (below) ? installing application plug-ins (page 145) ? connection problems after restart (page 146) upgrading the firmware follow this procedure to upgrade the firmware on your edgestore. downloading the upgrade file to download the upgrade file: 1. download the latest firmware upgrade file from www.edge10.com onto your pc. 2. copy the firmware upgrade file from your pc to a folder on the edgestore. installing the upgrade file 1. start the easm interface. 2. in the tree, click the + beside the management icon. 3. click the system upgrade icon. 4. from the volume dropdown menu, choose the volume that has the folder with the firmware image file. 5. from the folder dropdown menu, choose the folder that contains the firmware upgrade file. 6. in the file name field, type the name of the firmware upgrade file. 7. click the ok button to begin the upgrade. the upgrade takes about two to three minutes. when the upgrade is done, a system message appears. 8. click the ok button on the system message. 9. reboot the edgestore. see ?rebooting the edgestore? on page 144. warning do not disconnect the power or shut down the edgestore while the upgrade is running! free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 144 rebooting the edgestore during the reboot, none of your folders will be accessible from your networked pcs. to reboot the edgestore: 1. in the tree, click the + beside the system icon. 2. click the reboot / shutdown icon. 3. click the reboot option. 4. click the ok button. 5. in the confirmation box, click the ok button. the reboot runs automatically. when the edgestore is fully booted: ? the system status led turns green (right) ? the buzzer beeps one time (if the buzzer is enabled) see ?enabling and disabling the buzzer? on page 94. system status led free datasheet http://www.datasheet-pdf.com/
appendix b: maintenance 145 installing application plug-ins application plug-ins are enhancements to edgestore?s capabilities. the dlna server, which enables edgestore to support the upnp protocol, is one example of an application plug-in. follow this procedure to install an application plug-in on your edgestore. downloading the plug-in file to download the plug-in file: 1. download the plug-in file you want from www.edge10.com onto your pc. 2. copy the plug-in file from your pc to a folder on the edgestore. installing the plug-in file 1. start the easm interface. 2. in the tree, click the + beside the management icon. 3. click the system upgrade icon. 4. from the volume dropdown menu, choose the volume that has the folder with the plug-in file. 5. from the folder dropdown menu, choose the folder that contains the plug-in file. 6. in the file name field, type the name of the plug-in file. 7. click the ok button to begin the installation. when the installation is done, a system message appears. 8. click the ok button on the system message. 9. reboot the edgestore. see ?rebooting the edgestore? on page 144. warning do not disconnect the power or shut down the edgestore while the installation is running! free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 146 connection problems after restart if your edgestore?s network settings were set to obtain an ip address automatically , your dhcp server might assign a different ip address to the edgestore when you restart the edgestore after is was shutdown for repairs. this condition does not apply if you assigned your edgestore?s ip address manually. if you experience network drive or printer connection failures, check the edgestore?s current ip address. see ?finding the edgestore?s ip address? on page 21. if the edgestore?s ip address has changed, your previous network drives and printer connections will no longer work. here are two possible solutions: ? you may be able to reset the edgestore?s ip address manually. see ?changing the edgestore?s network settings? on page 53 or ?making network settings? on page 85. note that changing the edgestore?s ip address may cause an ip address conflict on your network. check with your network administrator before taking this action. ? if you cannot restore the previous ip address, you must create new network drives and printer connections. see ?chapter 3: connecting to the edgestore? on page 25. free datasheet http://www.datasheet-pdf.com/
147 appendix c: gnu general public license this product includes copyrighted third-party software licensed under the terms of the gnu general public license. please see the gnu general public license (?gpl?) for the exact terms and conditions of this license at www.gnu.org . the gpl source code incorporated into the product is available for free download at our web site at www.edge10.com . subject to gpl, you may re-use, re-distribute and modify the gpl source code. note that with respect solely to the gpl software, no warranty is provided, we do not offer direct support for the distribution. free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 148 free datasheet http://www.datasheet-pdf.com/
149 index a about this manual 1 action status, raid volume 79 ad domain 70, 128 add 80 email alert recipient 93 folder 64, 76 group 67 group member 67 raid volume 80 spare drive 81 user 63, 65 add printer wizard 34 administrator?s password, change 65 apc ups 95 application plug-ins 145 architecture, NAS400 2 audible alarm 111 authentication dialog box 27 b background activity, raid volume 79 backup performing 53 scheduling 56 backup files restore location 48 restoring 47 view 46 backup folder 46, 54 backup folder select 54 view 54 backup schedule create 44 delete 57 modify 57 backup server 86 backup software 4 browser path 12 browser support 4, 17 browser, default 58 buttons exit 50 extend file system 81 one touch backup 6, 45 open gui 19, 50 power 6, 121 reset 125 buzzer enable/disable 94 one beep 8 patterns 111 c cable, network 123 client os support 4, 5 computer name 88, 139 configuration tool 12 configure tool 8 connection, failed after restart 127, 146 connections network 7, 123 network drive 52 power 8 usb printer 31 connections, resolving 121 connectors network 6, 123 power 6 rj45 6 usb 6 usb drive 39 counter-sink screws 7 cpu temperature 99, 121 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 150 critical raid volume 114 d date and time 96, 136 date and time settings 13 dchp server 63 ddns 90 default browser, setting 58 default gateway 63, 88, 89, 139 delete device record 53 email alert recipient 93 folder 76 group 68 group member 67 raid volume 82 user 66 device name 15, 52, 141 dhcp server 13, 88, 138 disconnect usb drive 42 disk drive assign to raid volume 64 events 119 installing 7 replace 113 sata 7 view 80 disk drives, moving to a different edgestore 114 disk status led 112 display edgestores on network 50 dlna media formats 75 plug-in 74, 129, 145 server 74, 145 dns name, smtp server 92 dns server 63, 88, 89, 139 domain controller 70 domain name ad domain 70 ddns 90 drive letter 44 drive record, delete 53 dynamic domain name server 90 e easm connect to 59 connecting to 17 default browser 58 event log 116 in browser 18, 60 in smartsync 19, 61 language 62 navigating the interface 62 setup wizard 63, 101 starting 50 edgestore cannot connect after restart 127 enclosure info 99 finding ip address 17 locate 98 reboot 97, 144 restart 98 shut down 20, 98 unpacking 5 view system info 99 edgestores, on network, display 50 email alert list, view 93 email notification 124 enable one touch backup 87 enclosure events 118 status 120 error message, network drive 128 error message, not enough free disk space 128 esd warning 5 ethernet activity led 121, 123 ethernet hub or switch 7 free datasheet http://www.datasheet-pdf.com/
index 151 event log 116 clear 58 save to text file 58 view 58, 92 events disk drive 119 enclosure 118 file system 117 nas replication 118 raid volume 119 snapshots 118 system 118 events, response to 117 export access list, unix/linux pc 72 ext3 file format 39 f failed boot drive 56 fan speed 99, 121 fans cooling 6 power supply 6 fat16 file format 128 fat32 file format 39, 128 file protocol support 3 file system events 117 rebuilding 116 status 115 files backup 46 protected 43, 56 restore backup 47 finding edgestore?s ip address 17 firewall, windows 125 firmware, updating 143 folder add 64, 76 delete 76 ftp sharing 78 folder, cont. names 128 protected 43, 56 select for backup 44, 54 services 75 unix/linux sharing 77 view 75 view backup 54 windows sharing 77 formatting memory stick 83 raid volume 80 usb drive 83 free disks 80 ftp access setup 73 client encoding 73 clients 128, 129 sharing setup 78 g gnu general public license 147 group add 67 add member 67 delete 68 delete member 67 view 66 h hub, network 123 i icon, smartsync 19, 44, 49, 61 internal port in windows 126 invalid raid volume 114, 129 ip address edgestore 18, 21, 29, 60, 63, 86, 88, 89, 126, 139, 146 edgestore, finding 17 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 152 ip address, cont. nic 12 obtain from dhcp server 13, 88, 138 smtp server 92 unix/linux pc 25, 72, 77 j jumbo frames 89, 129 l language configuration tool 12 easm 62 nas setup wizard 13, 135 smartsync 49 leds disk activity 6 disk status 6, 112 ethernet activity 6, 121, 123 system status 6, 8, 82, 97, 98, 112, 121, 124 linux export access list 72 setup access 71 setup network drive 24 sharing setup 77 locate edgestore 98 m macintosh access, setup 72 macintosh, setup network drive 27 mail alerts 124 map network drive 23 maximum transmission unit (mtu) 89 media 75 media formats 75 memory stick format 128 formatting 83 view 83 migrate a raid volume 81 mirror raid 103, 106 mirror/stripe raid 105, 107 modify folder services 75 my network places 21 n nas replication enable/disable 86 events 118 schedule 86 setup 86 nas setup wizard 12, 101 cannot access edgestore 127 language 13, 135 nas utility installer 8 network connecting to 7 connection problems 123 connections, multiple 122 display edgestores on 50 network drive connecting 52 could not reconnect all 127 error message 128 windows 16, 142 network drive setup linux 24 macintosh 27 naming 47 unix 24 windows 21 network information, view 88 network servers 26 network settings, making 88 network time protocol (ntp) 96 networks, multiple 7, 12 free datasheet http://www.datasheet-pdf.com/
index 153 nis domain 71, 128 non-ascii characters in folder name 128 not enough free disk space error message 128 ntp synchronization, view 97 o one touch backup 6, 129 described 43 enable 43 perform 45 one touch backup, enable 87 os, client supported 4 p parity raid 104, 107 partition and format 108 password administrator?s 63 change administrator?s 65 change user?s 66 ddns 90 easm 18, 19, 51, 60, 61 edgestore 27, 29, 33, 35 nas setup wizard 15, 136 NAS400 37 restore default 124 smtp server 92 permissions, windows 71 personal firewall 127 plug-ins, installing 145 power button 121 power status 99 power, connecting to 8 primary server 86 print server, setup 32, 74 printer, name in linux 35 printing linux 34 macintosh 37 windows 32 protected folders and files 43, 56, 129 protocols supported 2 public folder 16, 22, 26, 52, 142 q quota set 68 view 68 r raid level 64, 79, 80 choosing 106 raid 0 102, 106 raid 1 103, 106 raid 10 105, 107 raid 5 104, 107 raid level, change 81 raid volume 7, 13, 16, 64, 75, 76, 80, 140, 142 automatic rebuilding 108 change raid level 109 critical 114 delete 82 events 119 formatting 80 invalid 114, 129 migrate 81, 109 partition and format 108 rebuild 114 recover 115, 129 status 113 view status 79 raid, introduction to 101 reboot edgestore 97, 144 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 154 rebuild file system 116 raid volume 114 recipient, email alert 129 add 93 delete 93 recover raid volume 115, 129 snapshot backup 85 replace disk drive 113 resolving connections 121 restart edgestore 98 restore backup files 47 location 55 performing 55 restore location, backup files 48 rj45 connector 7 s scan network interface 122 schedule pc-to-edgestore backup 56 snapshot backup 85 select backup folder 54 server (edgestore) name 139 service ddns 90 ftp 64 macintosh 64 unix/linux 64 service status, view 91 services, enable 64 settings network 88 quota 68 setup ftp access 73 linux printing 34 macintosh access 72 setup, cont. macintosh printing 37 nas replication schedule 86 print server 32 print server access 74 snapshot backup 84 unix/linux access 71 ups 95 windows access 70 windows printing 32 setup wizard in easm 63 shared folder 52 shut down 20, 98 smartsync 8, 12, 17, 121 close window 50 icon 44 language 49 open 49 quitting 50 smartwizard 8 advanced mode 135 express mode 13 smtp authentication 92, 129 snapshots events 118 recover backups 85 setup backups 84, 85 status 84 view 84 software, installing 8 spare drive add 81 explained 107 specifications 3 standalone 86 status disk drives 112 edgestore 112 enclosure 120 file system 115 raid volume 79, 113 free datasheet http://www.datasheet-pdf.com/
index 155 status, cont. service status 91 snapshot 84 system 112 ups 94 stripe raid 102, 106 subnet mask 63, 88, 89, 139 switch, network 123 system backup file 56 events 118 system status led 8, 82, 97, 98, 112, 121, 124 system temperature 99 t temperature, cpu 121 time zone 136 u udp option in windows 126 unicode support 129 unicode, folder name support 128 unix export access list 72 setup access 71 setup network drive 24 sharing setup 77 unpacking the edgestore 5 update firmware 143 upnp protocol 74, 145 ups 112 setup 95 view 94 usb drive connect 39 disconnect 42 file formats 39 formatting 83 raid volume on 80 usb drive, cont. view 83 windows shortcuts 128 usb printer, connecting 31 usbdisk 39, 41, 83 user add 63, 65 change password 66 delete 66 view 65 user name ddns 90 easm 18, 19, 51, 60, 61 edgestore 27, 29, 33, 35 NAS400 37 v view backup files 46 backup folder 54 disk drive 80 email alert list 93 enclosure info 99 event log 58, 92 folders 75 group 66 memory stick 83 nas replication schedule 86 network information 88 ntp synchronization 97 quota 68 raid volume status 79 service status 91 snapshots 84 system info 99 ups status 94 usb drive 83 users 65 free datasheet http://www.datasheet-pdf.com/
edgestore NAS400 user manual 156 w windows ad domain 70 firewall issue 125 setup access 70 setup network drive 21 setup sharing 77 workgroup 71 ? s t e r r e i c h : t e l . : 0 1 / 5 8 5 5 4 3 0 f a x : 0 1 / 5 8 5 5 4 6 0 d e u t s c h l a n d : t e l . : 0 7 6 1 / 5 9 2 1 0 0 f a x : 0 7 6 1 / 5 8 5 2 2 8 s c h w e i z : t e l . : 0 6 1 / 2 7 3 1 1 - 3 1 f a x : 0 6 1 / 2 7 3 1 1 - 3 9 h a n t z + p a r t n e r t h e u p g r a d e c o m p a n y ! w w w . h a n t z . c o m free datasheet http://www.datasheet-pdf.com/

▲Up To Search▲

Price & Availability of NAS400

	To Download NAS400 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .